New firmware release v1.16.0.b1 (LoRaWAN 1.0.2 multi-region support)

[aevraewrvaervea]

@aevraewrvaervea Thanks to the tip from @ssmith, using com3 instead of COM3 worked, despite the tool reporting the com port as being COM3 on Windows when the list command is used, and the erroneous example code, i.e.,

C:\Program Files (x86)\Pycom\Pycom Firmware Update>pycom-fwtool-cli.exe -v -p co
m3 -s 921600 flash -t SiPy.tar.gz

works where SiPy.tar.gz is the firmware file in the same folder.

[rskoniec]

@daniel I just wonder - if LoRaWAN in this release was updated to 1.0.2 why os.uname() shows lorawan='1.0.0' ?

[this.wiederkehr]

@Xykon: how can I use the updater tool to flash custom firmware using the pycom-fwtool-cli? I think there used to be an -f option which was used to specify the file. However, when using the latest release of the firmware updater tool 1.10.1.b2 I was not able to flash custom fw. Would you mind providing an example on how to achieve this?

[jcaron]

@this-wiederkehr You can use the -t option, providing the .tar.gz archive as an argument.

With a Pysense or Pytrack (running a recent firmware) and the --pypic option this makes upgrades much easier than they used to be.

[this.wiederkehr]

@jcaron awesome, thanks.

[danielm]

@this-wiederkehr
I had troubles to flash custom firmware using latest version of CLI tool and found out that for me it only works with -t parameter after flash:

pycom-fwtool-cli -v -p comXY -s 921600 flash -t custom_firmware.tar.gz

[Tombee]

@jcaron Where do I download the command line tool pycom-fwtool-cli ?
I am using the Windows 10 environment with Atom and pymakr addon and cannot find it under Program files (x86) or elsewhere. My objective is to setup LoRa as US915
I have flashed the the v1.16.0.b1 successfully using GUI and notice that with os.uname() it still shows lorawan='1.0.0'
However, I can only get a LoPy OTAA connection at 868.1 despite using the optional region=LoRa.US915 in main.py or config.py.

[MarcoBenini]

In Linux the firmware upgrade for LoPy using the command line procedure "./update" (pycom_firmware_update_1.10.1.b2.tar.gz) fails.

Error shown
"... usage: updater.py [-h] [-v] [-p PORT] [-s SPEED] [-c] [-x]
{list,chip_id,wmac,smac,sigfox,exit,flash,write,cb,nvs,ota,lpwan,erase_fs,erase_all}
...
updater.py: error: argument command: invalid choice: '4190208' (choose from 'list', 'chip_id', 'wmac', 'smac', 'sigfox', 'exit', 'flash', 'write', 'cb', 'nvs', 'ota', 'lpwan', 'erase_fs', 'erase_all')
..."

I tried downloading the firmware file for the LoPy (file LoPy-1.16.0.b1.tar.gz)
and use, as in downgrade firmware thread, the command
python bin/updater.py -t FIRMWARE_FILE_NAME.tar.gz -p SERIAL_PORT -s 921600 flash

It doesn't work since in the new bin/updater.py the command arguments were split in groups, while before where all put together.
So "flash" has to before "-t FIRMWARE_FILE_NAME.tar.gz".

So the command has to be:
python bin/updater.py -p SERIAL_PORT -s 921600 flash -t FIRMWARE_FILE_NAME.tar.gz

note: -s 921600 can be omitted since it is the default value
LoRa region Europe is default value.

[rskoniec]

@tombee It should be under C:\Program Files (x86)\Pycom\Pycom Firmware Update

[Tombee]

@rskoniec Thanks
It shows up on my Windows 7 computer in the Program Files(x86)
but NOT in my Windows 10 computer! Any ideas?

[Tombee]

@rskoniec I used C:\Program Files\Pycom\Pycom Firmware Update\pycom-fwtool-cli.exe --verbose -p com13 lpwan --region "US915"
but after a Connecting ........................................____ shows for about 15 seconds it ends with
Exception: Failed to connect to ESP32: Timed out waiting for packet header, on line 351
Suggestions?

[ssmith]

@tombee Press the reset button, Make sure all other programs that use the COM port are not connect, verify the the device is actually going into programming mode by opening a COM port and seeing the waiting for download message.

[Tombee]

@ssmith I pushed the reset button prior to each attempt and the LoPy flashed green.
I was able to install using the GUI version but seem stuck at getting the US915 region setup when using the command line version. I am using a Windows 7 64bit computer where I was able to find the Pycom Firmware Update directory. It doesn;t show up in my Windows 10 pc directories.

[Xykon]

@tombee From the output it looks like you are using an Expansion Board 2.0

Did you install the jumper wire the same way you do when using the GUI firmware update tool?

[Xykon]

@marcobenini I have uploaded a new version that should fix this. Please try downloading https://software.pycom.io/downloads/pycom_firmware_update_1.10.1.b3.tar.gz again.

I have made another small correction after uploading this release without increasing the version again, so if you've downloaded the new version earlier please try downloading it again.

If you still have issues with this version please let me know.

[ssmith]

@tombee Here's the command I used with no issues on a Win10 machine..
pycom-fwtool-cli -p com7 flash -t LoPy4-1.16.0.b1_Steve_mod.tar.gz
Sounds like the program is not even seeing the device from your error message. Verify that it is actually going into download mode. I didn't set the region in the download command.

[Tombee]

@xykon It is the same USB connector (com13) on the same Win7 pc. I can run the GUi update and it completes successfully. I can then connect with TeraTerm and run REPL
But it won't run the CLI version

I am using the pysense board. Don't have the expansion board to try. So I didn't use any jumper wire when using the GUI

[Xykon]

@tombee Do you have any anti-virus or security software installed?

[Tombee]

@xykon Windows Defender on Win10, AVG on WIn7.
I disabled AVG and tried again with different error
Invalid head of packet <'\xe4'>, on line 351.
PS: Since I don't have a reputation yet I must wait 600 seconds between posts :-(

[Xykon]

@tombee I think I know what the problem is. Are you OK to wait until tomorrow as you said the GUI version is working?