pyscan paper ink

[gael cobert]

ok thanks ! do you know how can i connect the HAT to the pyscan ?

[robert-hh]

@gael-cobert That depends. Pyscan makes heavy use of the Pins. And depending on the module used, even more pins are blocked. You can use all available pins.
3.3V -> 3.3V, e.g. at the Fingerprint sensor block
GND --> GND e.g. at the Fingerprint sensor block
DIN --> P19 at the fingerprint sensor
CLK --> e.g. P9
CS --> May be tied to GND, if you just connect one device
DC --> e.g. P10
RST --> e.g. P2, which is shared with the RGB led. You may also connect it to Reset. Then the display is reset wehn you push the butto.
BUSY -> P15 at the fingerprint sensor

[gael cobert]

@robert-hh hello thanks

when i start the program i have this error

File "<stdin>", line 33, in <module>
ValueError: invalid argument(s) value

line 33 is : miso = Pin(19)

SPIV on ESP32

sck = Pin(18)
miso = Pin(19)
mosi = Pin(23)
dc = Pin(32)
cs = Pin(33)
rst = Pin(19)
busy = Pin(35)
spi = SPI(2, baudrate=20000000, polarity=0, phase=0, sck=sck, miso=miso, mosi=mosi)

[robert-hh]

@gael-cobert In the Pycom world ĥave to write

sck = "P18"
miso = "P19"
mosi = "P23"

and then

spi = SPI(2, baudrate=20000000, polarity=0, phase=0, pins=(sck, mosi, miso))

You have to use either the Pxx numbers of the development board, or the Gxx numbers of the expansion board, but NEVER the GPIO numbers of the ESP32.

See: https://docs.pycom.io/firmwareapi/pycom/machine/spi/ and
https://docs.pycom.io/firmwareapi/pycom/machine/pin/#app

[gael cobert]

@robert-hh said in pyscan paper ink:

miso = "P19"

ok thanks !
this is a picture of the board / HAT and pin
https://drive.google.com/file/d/11vN_3IOCtbFyNRU48OogThDfdZR2UpcA/view

can you confirm miso = "P19"

what is miso and mosi ? because i have DIN, CLK, CS, DC etc

the new code :

# SPIV on ESP32
sck = "P18"
miso = "P19"
mosi = "P23"
#dc = Pin(10)
#cs = Pin(33)
#rst = Pin(2)
#busy = Pin(15)
spi = SPI(2, baudrate=20000000, polarity=0, phase=0, pins=(sck, mosi, miso))

and the error is now

Traceback (most recent call last):
  File "<stdin>", line 18, in <module>
OSError: resource not available

[robert-hh]

@gael-cobert Probing it with amultimeter it turns out, that the P15 and P19 at lower column, where you connectef the blue and lilac cable, are not connected to the socket for the xxPy module. However, the P15 amd P19 labeled pins at the upper socket, where you connected the green and yellow cable, are connected.
Also: you have to connect mosi to din of the pyper ink, not miso. miso is actually not used at all, so you can select e.g. p13 for it.

[gael cobert]

@robert-hh said in pyscan paper ink:

you have to connect mosi to din of the pyper ink, not miso. miso is actually not used at all, so you can select e.g. p13 for it.

ok thanks
this this a photo of the corrected pin
https://drive.google.com/file/d/121qPyq86FyFCAwZgKOXwRSW4PqKHniux/view?usp=drivesdk

i connected RESET pin in P11 --> https://drive.google.com/file/d/126aoKHjdVRYbr9yN0W114HpItaYDK5zA/view?usp=drivesdk

i don't know what is "mosi" and "miso"
i have din ( blue cable) connected to P19
so din must be connected to P13 or P19 ?

[robert-hh]

@gael-cobert It's easy to remember once you heard it:
mosi = Master Out Slave In
miso = Master In Slave Out

The connection looks OK.

[gael cobert]

@robert-hh

ok this is the setup code

rst = Pin('P11') --> ok ( white ) --> https://drive.google.com/file/d/126aoKHjdVRYbr9yN0W114HpItaYDK5zA/view?usp=drivesdk
dc = Pin('P10') --> ok ( green )
busy = Pin('P15') --> ok ( lilac )
cs = Pin('???') --> KO ( orange ) ?? connected to GND --> must i type Pin('GND')
clk = Pin('P9') --> ok ( yellow )
mosi = Pin('???') --> ????? don't understand --> i have no cable ...

spi = SPI(2, baudrate=20000000, polarity=0, phase=0, pins=(sck, mosi, None))

[gael cobert]

@robert-hh

ok this is the setup code

rst = Pin('P11') --> ok ( white )
dc = Pin('P10') --> ok ( green )
busy = Pin('P15') --> ok ( lilac )
cs = Pin('???') --> KO ( orange ) ?? connected to GND --> must i type Pin('GND')
clk = Pin('P9') --> ok ( yellow )
mosi = DIN = Pin('P15') --> blue cable

spi = SPI(2, baudrate=20000000, polarity=0, phase=0, pins=(sck, mosi, None))

[robert-hh]

@gael-cobert
since you have connected the cs pin of the device to GND, you can skip it in your code. I recommended that to save port pins. It requires howerver to change the code.
mosi is the pin for DIN of the display, used to send data to the display. So you have that connected to P19.
The SPI signal which you do not need is miso, because no data is read back from the display.

[gael cobert]

ok thanks it seems ok so now i have this error :

Traceback (most recent call last):
  File "main.py", line 76, in <module>
  File "/flash/lib/epaper7in5.py", line 135, in display_frame
IndexError: bytearray index out of range

"""
	Example for 4.2 inch black & white Waveshare E-ink screen
	Run on ESP32
"""

import epaper7in5
from machine import Pin, SPI

# SPIV on ESP32
 

rst = Pin('P11')
dc = Pin('P10')
busy = Pin('P15')
cs = Pin('P4')
clk = Pin('P9')
mosi = Pin('P15')


spi = SPI(0, mode=SPI.MASTER, baudrate=2000000, polarity=0, phase=0, pins=(clk, mosi, None))

e = epaper7in5.EPD(spi, cs, dc, rst, busy)
e.init()

w = 600
h = 384
x = 0
y = 0

# --------------------

# use a frame buffer
# 400 * 300 / 8 = 15000 - thats a lot of pixels
import framebuf
buf = bytearray(w * h // 8)
fb = framebuf.FrameBuffer(buf, w, h, framebuf.MONO_HLSB)
black = 0
white = 1
fb.fill(white)

# --------------------

# write hello world with black bg and white text
from image_dark import hello_world_dark
from image_light import hello_world_light
print('Image dark')
#bufImage = hello_world_dark
#fbImage = framebuf.FrameBuffer(bufImage, 128, 296, framebuf.MONO_HLSB)
#fb.blit(fbImage, 20, 2)
#bufImage = hello_world_light
#fbImage = framebuf.FrameBuffer(bufImage, 128, 296, framebuf.MONO_HLSB)
#fb.blit(fbImage, 168, 2)
#e.display_frame(buf)

# --------------------

# write hello world with white bg and black text
print('Image light')
#e.display_frame(hello_world_light)

# --------------------


print('Frame buffer things')
fb.fill(white)
fb.text('Hello World',30,0,black)
#fb.pixel(30, 10, black)
#fb.hline(30, 30, 10, black)
#fb.vline(30, 50, 10, black)
#fb.line(30, 70, 40, 80, black)
#fb.rect(30, 90, 10, 10, black)
#fb.fill_rect(30, 110, 10, 10, black)
#for row in range(0,36):
#	fb.text(str(row),0,row*8,black)
#fb.text('Line 36',0,288,black)
e.display_frame(buf)

# --------------------

# wrap text inside a box
black = 0
white = 1
# clear
fb.fill(white)
# display as much as this as fits in the box
str = 'Lorem ipsum dolor sit amet, consectetur adipiscing elit. Etiam vel neque in elit tristique vulputate at et dui. Maecenas nec felis lectus. Pellentesque sit amet facilisis dui. Maecenas ac arcu euismod, tempor massa quis, ultricies est.'

# this could be useful as a new method in FrameBuffer
def text_wrap(str,x,y,color,w,h,border=None):
	# optional box border
	if border is not None:
		fb.rect(x, y, w, h, border)
	cols = w // 8
	# for each row
	j = 0
	for i in range(0, len(str), cols):
		# draw as many chars fit on the line
		fb.text(str[i:i+cols], x, y + j, color)
		j += 8
		# dont overflow text outside the box
		if j >= h:
			break

# clear
fb.fill(white)

# draw text box 1
# box position and dimensions
print('Box 1')
bx = 8
by = 8
bw = 112 #  = 14 cols
bh = 112 #  = 14 rows (196 chars in total)
text_wrap(str,bx,by,black,bw,bh,black)
e.display_frame(buf)

# draw text box 2
print('Box 2 & 3')
bx = 0
by = 128
bw = w # 128 = 16 cols
bh = 6 * 8 # 48 = 6 rows (96 chars in total)
text_wrap(str,bx,by,black,bw,bh,black)

# draw text box 3
bx = 0
by = 184
bw = w//2 # 64 = 8 cols
bh = 8 * 8 # 64 = 8 rows (64 chars in total)
text_wrap(str,bx,by,black,bw,bh,None)
e.display_frame(buf)

# --------------------

[robert-hh]

@gael-cobert You have set MOSI to P15. That's not possible. and in fact you use P19

[robert-hh]

@gael-cobert In the epaper driver the dimension is set to 640x384, in your control code you use 600x384. These two setting must match.

[gael cobert]

@robert-hh
yes thanks
i checked the screen model
i have this one : 5.83inch-e-paper (waveshare website 640x480)
so
i changed the driver for : epaper5in83 (600x448)
but now i have this error

Traceback (most recent call last):
File "<stdin>", line 60, in <module>
File "/flash/lib/epaper5in83.py", line 136, in display_frame
IndexError: bytearray index out of range

"""
	Example for 4.2 inch black & white Waveshare E-ink screen
	Run on ESP32
"""

import epaper5in83
from machine import Pin, SPI

# SPIV on ESP32
 

rst = Pin('P11')
dc = Pin('P10')
busy = Pin('P15')
cs = Pin('P4')
clk = Pin('P9')
mosi = Pin('P19')


spi = SPI(0, mode=SPI.MASTER, baudrate=2000000, polarity=0, phase=0, pins=(clk, mosi, None))

e = epaper5in83.EPD(spi, cs, dc, rst, busy)
e.init()

w = 600
h = 448
x = 0
y = 0

# --------------------

# use a frame buffer
# 400 * 300 / 8 = 15000 - thats a lot of pixels
import framebuf
buf = bytearray(w * h // 8)
fb = framebuf.FrameBuffer(buf, w, h, framebuf.MONO_HLSB)
black = 0
white = 1
fb.fill(white)

# --------------------

# write hello world with black bg and white text
from image_dark import hello_world_dark
from image_light import hello_world_light
print('Image dark')
#bufImage = hello_world_dark
#fbImage = framebuf.FrameBuffer(bufImage, 128, 296, framebuf.MONO_HLSB)
#fb.blit(fbImage, 20, 2)
#bufImage = hello_world_light
#fbImage = framebuf.FrameBuffer(bufImage, 128, 296, framebuf.MONO_HLSB)
#fb.blit(fbImage, 168, 2)
#e.display_frame(buf)

# --------------------

# write hello world with white bg and black text
print('Image light')
e.display_frame(hello_world_light)

# --------------------


print('Frame buffer things')
fb.fill(white)
fb.text('Hello World',30,0,black)
#fb.pixel(30, 10, black)
#fb.hline(30, 30, 10, black)
#fb.vline(30, 50, 10, black)
#fb.line(30, 70, 40, 80, black)
#fb.rect(30, 90, 10, 10, black)
#fb.fill_rect(30, 110, 10, 10, black)
#for row in range(0,36):
#	fb.text(str(row),0,row*8,black)
#fb.text('Line 36',0,288,black)
e.display_frame(buf)

# --------------------

# wrap text inside a box
black = 0
white = 1
# clear
fb.fill(white)
# display as much as this as fits in the box
str = 'Lorem ipsum dolor sit amet, consectetur adipiscing elit. Etiam vel neque in elit tristique vulputate at et dui. Maecenas nec felis lectus. Pellentesque sit amet facilisis dui. Maecenas ac arcu euismod, tempor massa quis, ultricies est.'

# this could be useful as a new method in FrameBuffer
def text_wrap(str,x,y,color,w,h,border=None):
	# optional box border
	if border is not None:
		fb.rect(x, y, w, h, border)
	cols = w // 8
	# for each row
	j = 0
	for i in range(0, len(str), cols):
		# draw as many chars fit on the line
		fb.text(str[i:i+cols], x, y + j, color)
		j += 8
		# dont overflow text outside the box
		if j >= h:
			break

# clear
fb.fill(white)

# draw text box 1
# box position and dimensions
print('Box 1')
bx = 8
by = 8
bw = 112 #  = 14 cols
bh = 112 #  = 14 rows (196 chars in total)
text_wrap(str,bx,by,black,bw,bh,black)
e.display_frame(buf)

# draw text box 2
print('Box 2 & 3')
bx = 0
by = 128
bw = w # 128 = 16 cols
bh = 6 * 8 # 48 = 6 rows (96 chars in total)
text_wrap(str,bx,by,black,bw,bh,black)

# draw text box 3
bx = 0
by = 184
bw = w//2 # 64 = 8 cols
bh = 8 * 8 # 64 = 8 rows (64 chars in total)
text_wrap(str,bx,by,black,bw,bh,None)
e.display_frame(buf)

# --------------------

[gael cobert]

@robert-hh
hello i have another 4.2 paper ink screen (WFT0420CZ15)
so i changed the driver and the resolution (400x300), no more error but the screen do not respond / change :p

"""
	Example for 4.2 inch black & white Waveshare E-ink screen
	Run on ESP32
"""

import epaper4in2
from machine import Pin, SPI

# SPIV on ESP32
 

rst = Pin('P11')
dc = Pin('P10')
busy = Pin('P15')
cs = Pin('P4')
clk = Pin('P9')
mosi = Pin('P19')


spi = SPI(0, mode=SPI.MASTER, baudrate=2000000, polarity=0, phase=0, pins=(clk, mosi, None))

e = epaper4in2.EPD(spi, cs, dc, rst, busy)
e.init()

w = 400
h = 300
x = 0
y = 0

# --------------------

# use a frame buffer
# 400 * 300 / 8 = 15000 - thats a lot of pixels
import framebuf
buf = bytearray(w * h // 8)
fb = framebuf.FrameBuffer(buf, w, h, framebuf.MONO_HLSB)
black = 0
white = 1
fb.fill(white)

# --------------------

# write hello world with black bg and white text
#from image_dark import hello_world_dark
#from image_light import hello_world_light
print('Image dark')
#bufImage = hello_world_dark
#fbImage = framebuf.FrameBuffer(bufImage, 128, 296, framebuf.MONO_HLSB)
#fb.blit(fbImage, 20, 2)
#bufImage = hello_world_light
#fbImage = framebuf.FrameBuffer(bufImage, 128, 296, framebuf.MONO_HLSB)
#fb.blit(fbImage, 168, 2)
#e.display_frame(buf)

# --------------------

# write hello world with white bg and black text
print('Image light')
#e.display_frame(hello_world_light)

# --------------------


print('Frame buffer things')
fb.fill(white)
fb.text('Hello World',30,0,black)
#fb.pixel(30, 10, black)
#fb.hline(30, 30, 10, black)
#fb.vline(30, 50, 10, black)
#fb.line(30, 70, 40, 80, black)
#fb.rect(30, 90, 10, 10, black)
#fb.fill_rect(30, 110, 10, 10, black)
#for row in range(0,36):
#	fb.text(str(row),0,row*8,black)
#fb.text('Line 36',0,288,black)
e.display_frame(buf)

# --------------------

# wrap text inside a box
black = 0
white = 1
# clear
fb.fill(white)
# display as much as this as fits in the box
str = 'Lorem ipsum dolor sit amet, consectetur adipiscing elit. Etiam vel neque in elit tristique vulputate at et dui. Maecenas nec felis lectus. Pellentesque sit amet facilisis dui. Maecenas ac arcu euismod, tempor massa quis, ultricies est.'

# this could be useful as a new method in FrameBuffer
def text_wrap(str,x,y,color,w,h,border=None):
	# optional box border
	if border is not None:
		fb.rect(x, y, w, h, border)
	cols = w // 8
	# for each row
	j = 0
	for i in range(0, len(str), cols):
		# draw as many chars fit on the line
		fb.text(str[i:i+cols], x, y + j, color)
		j += 8
		# dont overflow text outside the box
		if j >= h:
			break

# clear
fb.fill(white)

# draw text box 1
# box position and dimensions
print('Box 1')
bx = 8
by = 8
bw = 112 #  = 14 cols
bh = 112 #  = 14 rows (196 chars in total)
text_wrap(str,bx,by,black,bw,bh,black)
e.display_frame(buf)

# draw text box 2
print('Box 2 & 3')
bx = 0
by = 128
bw = w # 128 = 16 cols
bh = 6 * 8 # 48 = 6 rows (96 chars in total)
text_wrap(str,bx,by,black,bw,bh,black)

# draw text box 3
bx = 0
by = 184
bw = w//2 # 64 = 8 cols
bh = 8 * 8 # 64 = 8 rows (64 chars in total)
text_wrap(str,bx,by,black,bw,bh,None)
e.display_frame(buf)

# --------------------

[gael cobert]

@robert-hh
if i skip cs in the code,
how can i init : e = epaper4in2.EPD(spi,cs , dc, rst, busy)
because it needs "cs" ....

[robert-hh]

@gael-cobert said in pyscan paper ink:

clk = Pin('P9')
mosi = Pin('P19')

No sign of life at all? no flickering? Check the wiring again.
I use the SPI constructor usually with the Pin names instead of Pin objects. That would then be:

clk = "P9"
mosi = "P19"

There are switches on the HAT. Did you set them accordingly. You are using the 4 wire SPI mode. And the display config switch must be at B.

[robert-hh]

@gael-cobert You assigned P4 to CS. So you can use that in the code, albeit cs is not connected to the display. The display has CS permanently active, since you wired it to GND. You can of course connect teh CS of the display to P4, or use P8, since you already soldered a connector to the bottom. But that seems not the problem here.

[gael cobert]

@robert-hh

no flickering at all, no sign of life :p
last photo
https://drive.google.com/file/d/12FfBYLkFZt49QnGn-oToWulc4fcd8lRR/view?usp=sharing

is it important to plug the RST cable ?

"""
	Example for 4.2 inch black & white Waveshare E-ink screen
	Run on ESP32
"""

import epaper4in2
from machine import Pin, SPI

# SPIV on ESP32
 

rst = Pin('P11')
dc = Pin('P10')
busy = Pin('P15')
cs = Pin('P4')
clk = Pin('P9')
mosi = Pin('P19')


spi = SPI(0, mode=SPI.MASTER, baudrate=2000000, polarity=0, phase=0, pins=(clk, mosi, None))

e = epaper4in2.EPD(spi, cs, dc, rst, busy)
e.init()

w = 400
h = 300
x = 0
y = 0

# --------------------

# use a frame buffer
# 400 * 300 / 8 = 15000 - thats a lot of pixels
import framebuf
buf = bytearray(w * h // 8)
fb = framebuf.FrameBuffer(buf, w, h, framebuf.MONO_HLSB)
black = 0
white = 1
fb.fill(white)

print('print hello world')
fb.fill(white)
fb.text('Hello World',30,0,black)
#fb.pixel(30, 10, black)
#fb.hline(30, 30, 10, black)
#fb.vline(30, 50, 10, black)
#fb.line(30, 70, 40, 80, black)
#fb.rect(30, 90, 10, 10, black)
#fb.fill_rect(30, 110, 10, 10, black)
#for row in range(0,36):
#	fb.text(str(row),0,row*8,black)
#fb.text('Line 36',0,288,black)
e.display_frame(buf)


# --------------------