Send Lora message to non pycom device

[jmarcelino]

Yes, the LPRS easyRadio system is based on the TI CC430F5137 and uses FSK not LoRa.

[pkilcoyne]

Thanks all,
so the EasyRadio modules not being LoRa I wasn't testing like with like...got it.

Many thanks,

Paul

[pkilcoyne]

@xykon said in Send Lora message to non pycom device:

aybe I'm missing something but I can't see any mention of that thing using LoRa.

I found this, which mentions LoRa, on their website:

http://www.lprs.co.uk/products/easyradio-ism-modules/era-lora-through-hole-modules.html

Curious...

[Xykon]

@pkilcoyne That is not the same module you linked in your initial post.

Can you please confirm which module you're trying to use?

[pkilcoyne]

@xykon said in Send Lora message to non pycom device:

Can you please confirm which module you're trying to use?

Yes sorry about my first post, the latter module is the one I'm actually using, the ERA-LORA.

For the ERA-LORA there is a companion software where you can select the following attributes:

Radio power level: P9 - the highest
Channel: 0 ( 0-31)
bandwidth: 500kHz
band plan: b0 - 869.85MHz
Spreading Factor: SF10

I just don't know how to match the above with the LoPy modules so they can communicate.

Regards,

Paul

[pkilcoyne]

@jcaron

os.uname()
(sysname='LoPy', nodename='LoPy', release='1.10.1.b1', version='v1.8.6-839-g536c958c on 2017-11-15', machine='LoPy with ESP32', lorawan='1.0.0')

Antenna attached.

I don't know how to match band plan / channel to the frequency I'm sending on :(

Do you mean UART data rates or rates at which I send over the air? Not sure how to adjust these.

Thanks,

Paul

[jmarcelino]

@pkilcoyne
All the information you need how to set the module and what frequencies their “channels” really mean is in their datasheet.
http://www.lprs.co.uk/assets/files/eRA_LoRa_FCC_V1.22.pdf

You just need to come with with a common set of values for both modules and in the LoPy case set those when initializing the LoRa class

[pkilcoyne]

@jmarcelino said in Send Lora message to non pycom device:

set

Hi again,
thanks for the link, I've looked through it and I've matched relevant parameters. Also, I've contacted the manufacturer and they said I also need to match the "group ID", default is 1234, but I cannot see any reference to this parameter in the Pycom documentation.

Any ideas?

Thanks,

Paul

[jmarcelino]

@pkilcoyne
Group ID is not a LoRa radio parameter so I'd guess it's just some data that gets sent - like a number prefix.

Once you match the two unit's radio parameters try to see if you receive any data on the LoPy if you try to send from your device... maybe the Group ID will show up there.

I guess you can also ask the manufacturer to explain what Group ID is.

[pkilcoyne]

@jmarcelino Hi again,
so what I've done since is send messages between two LPRS devices sucessfully. The LoPy does not seem to receive these messages nor does it's programmed TX messages be received by either LPRS device.

Right now I have two parallel "lora" networks, one of two LPRS devices sending and receiving messages and one of two LoPy devices.

Maybe they just aren't meant to work together.

Paul

[jmarcelino]

@pkilcoyne
What does your LoRa initialisation look like? Are you setting LoRa.BW_500KHZ etc?

You may have to play with the public and rx_iq settings. Sorry I don’t know what your other device expects for those.

[pkilcoyne]

@jmarcelino Hello again,
thanks for your reply, below is my current script on the LoPy:

from network import LoRa
import socket
import machine
import time
# initialize LoRa in LORA mode
# more params can also be given, like frequency, tx power and spreading factor
lora = LoRa(mode=LoRa.LORA, frequency=869850000, sf=10, bandwidth=LoRa.BW_250KHZ, public=True)
# create a raw LoRa socket
s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)

counter = 0
while True:
    # send some data
    s.setblocking(True)
    s.send('Hello_from_LoPy')
    print('Hello_from_LoPy...{}'.format(counter))
    counter += 1

    # get any data received...
    s.setblocking(False)
    data = s.recv(64)
    print(data)
    if counter >= 100:  # reset counter at 100
        counter = 1
    time.sleep(1)
    # wait a random amount of time
    time.sleep(5)
    #time.sleep(machine.rng() & 0x0F)

[pkilcoyne]

@jmarcelino said in Send Lora message to non pycom device:

You just need to come with with a common set of values for both modules and in the LoPy case set those when initializing the LoRa class

Hi again, sorry for the delay in the update. So below is what I've set my LOPY to:

lora = LoRa(mode=LoRa.LORA, region=LoRa.EU868, sf=12, frequency=869850000, bandwidth=LoRa.BW_125KHZ, public=True)
s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)

Seems fairly standard, but what does the "public" parameter do?

On the ERA-LORA side via the companion GUI software I have the following st:

Bandplan (frequency): 869.85MHz
Bandwidth: 125KHz
Channel: 0
Spreading Factor: 12

This seems to be a match on both sides though I still cannot get them to communicate :(

Does the LOPY use any encryption by default?

Any other defaults I need to be aware of?

Thanks,

Paul