Welcome to the Pycom forum Forum
    • \[\[global:header.categories\]\]
    • \[\[global:header.recent\]\]
    • \[\[global:header.tags\]\]
    • \[\[global:header.popular\]\]
    • Login

    Explore Pybytes | Official Documentation | Report a Firmware Bug/Issue | GitHub

    Exp. board 3.0: Where is documentation for jumpers? I cannot find it

    Scheduled Pinned Locked Moved Expansion Board
    expansion boardjumpersjumperv3.0
    13 Posts 4 Posters 1.8k Views 4 Watching
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • danD Offline
      dan
      last edited by

      Hi @andrejpekarcik,

      You can find the pinout sheet for the Expansion Board 3 here.

      robert-hhR A P 3 Replies Last reply Reply Quote 0
      • robert-hhR Offline
        robert-hh @dan
        last edited by

        @dan This link seems misleading in two aspects:
        a) the question which was raised (jumpers?) is not answered
        b) the GPIO numbers in the link do not match any of the new Pycom boards. They seem to match WiPy1

        1 Reply Last reply Reply Quote 0
        • danD Offline
          dan
          last edited by

          @andrejpekarcik The jumpers are same as in the ExpBoard2, in its pinout (that @robert-hh linked) you can see what they do (bottom left section).

          @robert-hh what do you mean they don't match the boards? the GPIO pins match the pins on the Expansion Board

          robert-hhR 1 Reply Last reply Reply Quote 0
          • robert-hhR Offline
            robert-hh @dan
            last edited by

            @dan Sure, but which GPIO's are these? Or do say that these names match the GPIO pin names, which at some time in the past were GPIO's of a certain CPU?

            danD 1 Reply Last reply Reply Quote 0
            • danD Offline
              dan @robert-hh
              last edited by

              @robert-hh Correction: there are some issues with the pinout sheet, the pin labels have been mixed up. We'll update it with the correct labels.

              1 Reply Last reply Reply Quote 0
              • A Offline
                andrejpekarcik @dan
                last edited by

                @dan Thanks a lot. Function of jumpers should be explained also in Exp. board 3.0 docs with more details. I do not understand what it means to "Enable TX/RX/CST/.. signal".

                robert-hhR danD 2 Replies Last reply Reply Quote 0
                • robert-hhR Offline
                  robert-hh @andrejpekarcik
                  last edited by

                  @andrejpekarcik That's kind of obvious. There is am USB/UART bridge on the expansion bord, which coverts USB messages into a serial data stream, and RX, TX, CTS and RTS are data and cotrol signals of this stream. The jumpers are in the wire connecting the USB/UART bridge to the xxPy device socket.

                  RX receive data
                  TX transmit data
                  RTS request to send
                  CTS clear to send

                  RX and TX are mandatory, RTS and CTS are optional.

                  1 Reply Last reply Reply Quote 0
                  • A Offline
                    andrejpekarcik
                    last edited by

                    This post is deleted!
                    1 Reply Last reply Reply Quote 0
                    • P Offline
                      Prx @dan
                      last edited by

                      @dan link to exp board brocken

                      robert-hhR 1 Reply Last reply Reply Quote 0
                      • robert-hhR Offline
                        robert-hh @Prx
                        last edited by

                        @prx You can still find it on the pages for Expansion board 2 https://docs.pycom.io/datasheets/boards/expansion2 and you can see it on the pictures for the Exp Board 3 Pin-Out, which show what is printed on the board.
                        https://firebasestorage.googleapis.com/v0/b/gitbook-28427.appspot.com/o/assets%2F-LIL0iGdl11z7Jos_jpX%2F-LKN7scqKKkb6TqB3uYO%2F-LKN82UNLD-yPfdRcqkf%2Fexpansion3-pinout.pdf?generation=1534782103416626&alt=media

                        1 Reply Last reply Reply Quote 1
                        • danD Offline
                          dan @andrejpekarcik
                          last edited by

                          @andrejpekarcik we are working on an updated version, I'll add it to my list and see what we can do. Thanks for the feedback!

                          1 Reply Last reply Reply Quote 0

                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                          With your input, this post could be even better 💗

                          Register Login
                          • 1 / 1
                          • First post
                            Last post

                          Pycom on Twitter

                          Pycom