power supply (Lopy4+Exp.Board v.3)

[Giorgio]

Hi, I have this question:
Which is the minimum current that is possible to have in a sort of power down with a Lopy4 mounted on an expansion board 3? And in which way?(deep sleep -- go to sleep.... -- )?
I obtained 3,5mA at best. Is it possible to arrive at the order of uA?
Thanks in advance for your help.
Giorgio

[Paul Thornton]

With everything shut down and sleeping LTE/Wifi/Lora and the expansion board ect you should be seeing way less than 3.5mA

Ive seen 32uA with a LoPY 3 + an Expansion board v 3.1.

If you'd like to post the code perhaps we have work out whats going on :)

[Giorgio]

This post is deleted!

[Giorgio]

@paul-thornton This is the code (below). At the end of main.py I use the machine.deepsleep(10000)...
...is machine.deepsleep() sufficient in order to shut down everythings?
Then I use also a library for HX711 (for load cell) and a config.py file for Lorawan parameters
thanks.

print('\n\nVERSION 0x01\n\n')

"""importo libreria per LoRa"""
from network import LoRa

"""importo libreria machine per deep sleep"""
import machine
"""importo libreria machine per RTC"""
from machine import RTC
rtc=RTC()
rtc.ntp_sync("pool.ntp.org")
#rtc.init((2018,11,30,15,45,0))
#print(rtc.now())
import time
time.sleep(3)

"""importo libreria machine per ADC"""
from machine import ADC
adc = ADC()
battread = adc.channel(attn=0,pin='P16')
batt=battread()
print("VALORE DI BATTERIA ", batt)
"""importo vari moduli Python utili"""
import pycom
import socket
import ubinascii
import struct

import config

"""importo libreria per HX711"""
from hx711 import HX711

#---------------------------------------------------------------------------
"""Setup per LoRaWAN """
# initialize LoRa in LORAWAN mode.
# Please pick the region that matches where you are using the device:
# Asia = LoRa.AS923
# Australia = LoRa.AU915
# Europe = LoRa.EU868
# United States = LoRa.US915
lora = LoRa(mode=LoRa.LORAWAN, region=LoRa.EU868)

# create an OTA authentication params
dev_eui = ubinascii.unhexlify('0004A30B001BD398')
app_eui = ubinascii.unhexlify('70B3D57ED00140CB')
app_key = ubinascii.unhexlify('5C777F91BAFE83DD6C8651CC7873DDA7')

# set the 3 default channels to the same frequency (must be before sending the OTAA join request)
"""HO commentato 3 righe per il set delle frequenze sui canali 0, 1, 2,
	In questo modo posso usare più canali. NON va bene per il nanogateway che vuole solo un canale"""
lora.add_channel(0, frequency=config.LORA_FREQUENCY, dr_min=0, dr_max=5)
#lora.add_channel(1, frequency=config.LORA_FREQUENCY, dr_min=0, dr_max=5)
#lora.add_channel(2, frequency=config.LORA_FREQUENCY, dr_min=0, dr_max=5)

# join a network using OTAA
lora.join(activation=LoRa.OTAA, auth=(dev_eui, app_eui, app_key), timeout=0, dr=config.LORA_NODE_DR)

# wait until the module has joined the network
prove=0
freq=machine.freq()
#uni_id=machine.unique_id()
print(freq)
#print(uni_id)

while not lora.has_joined():
    time.sleep(2.5)
    print('Not joined yet...')
    prove+=1
    if(prove==5):
		break
if (prove<5):
    join=1
    print('Joined to LoRaWAN Network')
    # remove all the non-default channels
    for i in range(3, 16):
		lora.remove_channel(i)
    # create a LoRa socket
    s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)

	# set the LoRaWAN data rate
    s.setsockopt(socket.SOL_LORA, socket.SO_DR, config.LORA_NODE_DR)

	# make the socket non-blocking
    s.setblocking(False)
else:
    print('Not joined to LoRaWAN Network')
    join=0


""" Your own code can be written below! """
time.sleep(5.0)
"""FINE SETUP PER LoRaWAN"""
#---------------------------------------------------------------------------
#---------------------------------------------------------------------------
"""Setup per HX711 """
"""imposto il valore di offset - non mi serve la tara
#è il peso del sistema a vuoto senza pesi sopra """
hx = HX711('P15', 'P11') #DAT, clk
hx.set_offset(400500)	#è la tara senza peso sopra da togliere alla misura(iniziale 380600)
reference_unit = 745.500 #calcolato con peso di 5000gr (iniziale di 743.500)
"""FINE SETUP PER HX711"""
#---------------------------------------------------------------------------
for i in range(1):
	#leggo un valore dalla bilancia
    value = hx.get_value(10)
    print("Read VALUE: ", i)
    grammi = value/reference_unit #calcolo il peso della bilancia
    kg = grammi/1000
    print('             ')
    print('grammi: ', grammi, 'Kg: ',kg)
    print('             ')

	#leggo un valore di temperatura
	#trasformo i valori in byte
    if(kg < 0):
		kg=kg*(-1)	#tolgo i valori negativi
    kg1=int(kg*100) #*100 come se avesse due decimali-prendo la parte intera
    print(kg1)
    hi=kg1>>8 #prendo il byte alto
    lo=kg1-(hi<<8) #prendo il byte basso
    print("kg1: ", kg1, hex(kg1), "hi: ", hex(hi), "lo: ", hex(lo))
    print("sending...")
    pkg=bytes([1,2])+bytes([hi,lo]) #formato LPP - Cayenne -
    #if(join==1):
    #    s.send(pkg)
    #time.sleep(30)
	#trasmetto in lorawan
	#leggo da lorawan
    #leggo la batteria in add_channel
    batt=battread()
    print("VALORE DI BATTERIA ", batt)
    batt=int(batt/10)
    batHi=batt>>8
    batLo=batt-(batHi<<8)
    pkg1=bytes([2,2])+bytes([batHi,batLo]) #formato LPP - Cayenne -
    pkg2=pkg+pkg1
    if(join==1):
        s.send(pkg2)
    time.sleep(30)


print("entro in deep sleep")
machine.deepsleep(10000) #10sec to test

[Giorgio]

@paul-thornton ... and in the boot.py file I have this code:

# boot.py -- run on boot-up
import os
from machine import UART
uart = UART(0, 115200)
os.dupterm(uart)
#disable the wifi radio
from network import WLAN
wlan=WLAN()
wlan.deinit()
#disable the bluetotth radio
from network import Bluetooth
blt=Bluetooth()
blt.deinit()