New Firmware Release 1.20.2.rc6

[dgerman]

@peterp Thank you for your response.
After erase_all and flash I expect GPy to be blinking heartbeat and to be in Acces Point mode broadcasting SSID of gpy-wlan-xxxx (where xxxx are low order digits from MAC) with a password of www.pycom.io with a telnet server and ftp server running at 192.168.4.1 .
This is what I expect now but it seems to broadcast SSID only once (or a few times) ( I am using Mac Boot Pro , Catalina 10.15.4 which prior to flash 1.20.2.rc6 offered to connect and the airport utility continuously reported it's RSSI.)

[peterp]

@dgerman Understood. And are you able to test that AP behaviour after temporarily removing your boot.py and main.py?

[dgerman]

@peterp After erase_all and flash my boot.py and main.py are no longer there as I can tell by the heartbeat.
I cannot connect to Access Point to put them there.
Using

sudo iwlist wlan0 scan 

on a Raspberry PI Zero W reports

          Cell 06 - Address: 80:7D:3A:94:7B:7D
                    Channel:6
                    Frequency:2.437 GHz (Channel 6)
                    Quality=70/70  Signal level=-40 dBm
                    Encryption key:on
                    ESSID:"gpy-wlan-7b7c"
                    Bit Rates:5.5 Mb/s; 11 Mb/s; 1 Mb/s; 2 Mb/s; 6 Mb/s
                              12 Mb/s; 24 Mb/s; 48 Mb/s
                    Bit Rates:54 Mb/s; 9 Mb/s; 18 Mb/s; 36 Mb/s
                    Mode:Master
                    Extra:tsf=0000000000000000
                    Extra: Last beacon: 30ms ago
                    IE: Unknown: 000D6770792D776C616E2D37623763
                    IE: Unknown: 01088B9682840C183060
                    IE: Unknown: 32046C122448
                    IE: Unknown: 030106
                    IE: Unknown: 0706434E00010D14
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (2) : CCMP TKIP
                        Authentication Suites (1) : PSK
                    IE: Unknown: 2D1A6E1100FF00000000000000000000000100000000000000000000
                    IE: Unknown: 3D1606050000000000000000000000000000000000000000
                    IE: Unknown: DD180050F2020101040003A4000027A4000042435E0062322F00

I notice the only difference between multiple reports is

• Extra: Last beacon: 30ms ago
• Extra: Last beacon: 2070ms ago
• Extra: Last beacon: 4260ms ago

Which seems to confirm my suspicion that GPy is only broadcasting SSID once.
I don't know how to interpret anything else in the report.

If I download and flash a previous version of the firmware for GPy where should I get it? I am using a Mac so how do I get Pycom Firmware Update.app to flash a specific version?

[peterp]

@dgerman said in New Firmware Release 1.20.2.rc6:

@peterp After erase_all and flash my boot.py and main.py are no longer there

Ugh, yeah, of course. Sorry, wasn't thinking along properly here. Mhm ... it's weird ... I'm thinking ...

I cannot connect to Access Point to put them there.

just for completeness, you know you can work with pymakr?

If I download and flash a previous version of the firmware for GPy where should I get it? I am using a Mac so how do I get Pycom Firmware Update.app to flash a specific version?

you should be able to select previous version also in the application ... if you want to download them manually, see here https://software.pycom.io/downloads/GPy.html

[dgerman]

@peterp Thanks. On Mac OS with Pycom Firmware Update.app include develop versions I choose
GPy-1.20.2.rc2 ++SUCCESS++
GPy-1.20.2.rc3 --FAILS only transmits SSID once---
GPy-1.20.2.rc2 --FAILS !-!
GPy-1.20.2.rc2 with erase file system ++SUCCESS++

Did not see rc4 or rc5.

[dgerman]

@peterp Should I create an issue at GitHub?

[robert-hh]

@dgerman Can you show the full log you see in a console window after pushing reset?

[dgerman]

@robert-hh Sorry I don't understand what you are asking for.
Summary:
GPy 1.18.1.r2 (as received)
boot.py set LED green, pink, connects to wlan as STAtion and finally green.
main.py updates time from ntp sets LED blue then sends syslog message.
After update to 1.20.2.rc6 LED blinks but no syslog message is received. GPy does not respond to ping, telnet or ftp.
After erase_all and update, LED shows heartbeat (since boot.py and main.py were initialized as empty). GPy transmits SSID as AccessPoint one time only and macBookPro can no longer connect.

[robert-hh]

@dgerman If you connect your GPy to a terminal emulator and push the reset button, then you'll get some messages. These are the ones I'm asking for. Sample witth a LoPy4 below:

ets Jun  8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff8020,len:8
load:0x3fff8028,len:2140
ho 0 tail 12 room 4
load:0x4009fa00,len:19760
entry 0x400a05bc

Pycom MicroPython 1.20.2.rc6 [v1.20.1.r2-115-g5e92391-dirty] on 2020-04-08; LoPy4 with ESP32
Type "help()" for more information.
>>> 

[dgerman]

@robert-hh I only ever connect to GPy in the traditional headless manner (I initially only had a GPy board , no expansion board, no USB). I created a boot.py to set it up as a STAtion, established a wifi connection on MacBook Pro to the SSID gpy-wlan-7b7c and ftp'ed boot.py. After reset I use ftp to update boot.py and main.py. I telnet to it test code snippets in REPL.

If you provide me code to retrieve the values you are interested in I can use REPL to display them or I can put them in a main.py and write the values to a file and retrieve it with ftp.

[rcolistete]

Any change log of firmware 1.20.2.rc7 ?
It is not cited in the GitHub releases page :
https://github.com/pycom/pycom-micropython-sigfox/releases