PyGate with LoPY4 - High Power Consumption on Deep Sleep

[rcolistete]

@robert-hh Thanks, it was a typo error.

[rcolistete]

Another option is to modify "robert-hh / ATTiny-Watchdog-for-MicroPython" repository to use the ATTiny (85, etc) to turn on/off PyGate with LoPY4 using a MOSFET.

ATTiny 85 power usage :

• active mode, approx. 0.7-3.6 mA @ 3.0V 1-8 MHz;
• in deepsleep mode : 0.1-0.2 uA @ 3.0V without interrupts, 5 uA with interrupts.

http://www.technoblogy.com/show?KX0
https://www.re-innovation.co.uk/docs/sleep-modes-on-attiny85/
https://arduino.stackexchange.com/questions/13983/attiny85-power-consumption-vs-clock-speed

[anikolaid]

@rcolistete Thank you for elaborating on this! I had assumed that Pycom products don't need any kind of h/w modification in order to support low-power...The fact that I'm still to measuring 10-12mA in deep sleep mode (even trying the available methods, i.e. pybytes.deepsleep, machine.deepsleep) is really strange for a product series claiming to have been designed for low-power IoT applications.

[rcolistete]

It is really hard to find any low power LoRawan gateway, as gateways are designed to work 24/7.

[Gijs]

Did you remove the jumper on the header on the PyEthernet module? You can find this next to the large magnetics IC. This jumper allows for a basic current draw for some PoE modules, or they will switch off completely. I believe the current is indeed close to 10mA, but Im not exactly sure. Removing the small jumper removes the default load from the circuit.
Best,
Gijs

[anikolaid]

@Gijs Thank you for your recommendation. I don't use the PoE module, only Lopy4 connected to the PyGate. I use (and measure) the current of external power (i.e. Li battery) port of the PyGate.

[Gijs]

Sorry, read too quickly.

For your solution, I believe the external watchdog timer would be preferable. We have no sort of deepsleep built into the Pygate, like the Pysense 2 and Pytrack 2 have, where the power to the development module is cut off, having only the USB controller pic running to keep track of time, as the general use-case of the Pygate is to be on all the time. You could still try to desolder the LEDs and cut some power there. Other than that, I dont think it is possible without hardware / firmware modifications.

[anikolaid]

@Gijs Thank you for saving me a lot of time! I think it would be a good idea to clarify that in the PyGate datasheet.

[anikolaid]

@rcolistete thank you for indicating this! I've just purchased 2 items of the Nano Power Timer.
I've followed all the instructions given here but it does not work. To be more specific:

1. I have connected the power (5V) to the Vin pins and the Vout pins are powering the Extension Board v3.0 (with a LoPy4) via the USB connector of the Ext. Board.

2. Also, I connected the output pin P19 to the DONE pin of the Nano Power.

3. Delay via Dip Switch: 1 min

The issue: Once I plug-in the external input (5V) to the Nano Power, the Extension Board never turns on. If I put the push button of the Nano Power for 1 second then the Extension Board turns on for around 15 seconds and then turns off again.

Any ideas?

[rcolistete]

I've tested the SparkFun Nano Power Timer board some months ago, it was working ok, but it wasn't powering Expansion Board.

What about :

• using LiPo/LiIon battery to avoid any USB cable to power Expansion Board ?
• powering LoPy4 directly, from Vin (3.0-5.5V) ?

Why 15 s ? Is there any code in LoPy4 enabling the DONE pin of the Nano Power Timer ?