Getting started with PyGos and Pylife

[bomtarnes]

Mine never gets as far as showing the wifi access point.

[arikb]

@bomtarnes I get it to show the access point by going through the firmware update process in the app. At least for me (Android, PyLife app version 1.0.9) when the firmware update process fails, it leaves the unit in a mode with the access point turned on. Then I disconnect the phone's Wi-Fi (if still connected) and then connect from my computer.

[Peter Bankuti]

@arikb I can not get to starting the firmware update in the app. I get stuck during the scan process, where i should give the PyGo an alias name. The android app on my phone (Samsung Galaxy S7 with stock Android 8.0.0) does not accept anything no matter what i type there as input. (Tried also any formatting i can just think of). All i get is NOT_VALID_DEVICE response from the app and the PyGo does not turn on as an AP. Can you please tell me on what phone/Android version is working on your side?

[arikb]

@Peter-Bankuti I have a OnePlus 5T with a (rather old) CyanogenMod OS based on Android 9. Had no trouble at all scanning and adding and naming the devices.

[Ralph Lohse]

@bomtarnes +1

[Keptenkurk]

@bomtarnes +100 a few more months waiting would have been better than shipping useless bricks. My PyGo1 and 2 are plain dead. Now waiting for a magical revival due to battery discharge. As a backer you choose to go the bumpy road, but this journey has been far beyond expectations in all aspects...

[Stephen Glavin]

Thanks. I’ve now managed to update both using a PC. However, as other users are finding, they just won’t charge on the charging pad. After 5 hours still 0% on one and 2% on the other. The charging pad itself regularly has a flashing blue light which I assume is its own thermal protection. @Pete-Allen-0

[henri lepervier]

@Ralph-Lohse @Pete-Allen-0 @bomtarnes +1 also

[henri lepervier]

@Edouard-Abramovich @Pete-Allen-0 +1, I am now exactly at the same stage. After the reboot, I get BT, but Wifi-local is no more available.

[henri lepervier]

@henri-lepervier @Pete-Allen-0 @Peter-Bankuti @bomtarnes
Hello Pete, All,
Finally, I have understood (sorry I am slow) that this was possible to use the Wifi Local network to try the Firmware upgrade manual procedure. I did it, and after several attempts, it worked !

Then I started from scratch. I had difficulties to have a positive scan for the PyGo (dozen of attempts), but eventually, it was recognized by the Android OS Pylife application

I though I was at the end of the story... but unfortunately no.

1/ The device cannot charge more than 1% (using a QI Wireless Charger)
2/ and more : the location stays wrong : I have a plot in the middle of the blue (without any google map all around)

I have spent a lot of time to reach this point

And now, my question : I received a box with a sticker Pygo2 (so I used the PyGo2 firmware), but when I look to the device, there is no slot for a SIM card as presented into the documentation

Do you have the same ? is there a Sim slot on your devices ? I am wandering if all my issues are not due to a wrong PyGo (1 instead of 2)

For the time being, I am stuck : the device cannot charge, even with the Firmware updated to the latest version.

Any recommendation would be greatly appreciated

Kind regards
H.

[Stephen Glavin]

Update again. Both now just state 0% battery and only turn on when sitting on the charger. I left one charging overnight ~10 hours and in the morning it was still 0%. My conclusion is that neither will charge and the batteries are completely dead. @Stephen-Glavin @Pete-Allen-0

[Edouard Abramovich]

@Stephen-Glavin I noticed the battery percentage is not updated until the device goes to sleep mode. Once it is on again, the app displays the correct value. The overheating issue might still get in the way though. I put my charger in the freezer and managed to charge the battery halfway.

[Andrew Mills]

@henri-lepervier I ordered (and think) that I have received a pygo 1 + pygo 2. My pygo2 does not have a sim card slot. Having the issues upgrading firmware on it so can't confirm if it has a IMEI number (which I think indicates the unit can connect to cellular network).

[Stephen Glavin]

I like the ingenuity, but it’s not very practical and would make wired charging just as convenient :) Hopefully this is just a firmware issue. But a bit disappointing that I can’t even test two pygos communicating as they each only have power when charging, and there’s only one charger. @Edouard-Abramovich

[Peter Bankuti]

@Stephen-Glavin Maybe in another 4 years also pycom will respond to this shambolic product release. But until then it seems we as users should somehow reverse-engineer everything and try to find a solution instead of them. The very least pycom should have communicated by now is that they have an issue and we should not do anything with the delivered devices until they fix all the issues in the firmware that actually prevent us using the pygos. Really have no words how it is being handled.

[Andrew Mills]

This post is deleted!

[arikb]

I have the same problems as @Stephen-Glavin @henri-lepervier @Edouard-Abramovich.

My PyGo still heats up a lot, and stops charging after a while. I'm trying to figure out the status LED on the wireless charger.

So far I've seen several behaviours, and I'm trying to fill in the blanks.

Green-blue-green - booting
Solid blue - charging
Blinking ~0.5Hz teal - overheating?

[Andrew Reekie]

@Andrew-Mills They must have went back to an embedded SIM solution. I have manged to upgrade one of my pygo2's and app does now show an IMEI ID #.

[henri lepervier]

@arikb @Pete-Allen-0 @Edouard-Abramovich @bomtarnes @Stephen-Glavin

Status of tonight : I went outside to buy a new QI wireless charger (yeaaa) : larger one - a square like 7 x 7 cm. Still plugged on my PC USB port. I reached 6% !

Also, BT is on. Pygo is recognized by the Android OS application. But no clue why the WiFi Local network is gone : I suspect this is available only when a Firmware update is possible.

Still the GPS location is completely wrong (I am NOT living in the middle of the Atlantic Ocean)

Still very hot in any case.

No time to verify, but I have the suspicion that the device is charging only after an interaction (like trying to Fupgrade, or asking for a status)...

Anyway, this is quite far from a robust status ... and I still do not understand why there is no SIM slot somewhere as per the documentation

That all for tonight

Kind regards
H.

[henri lepervier]

@henri-lepervier

and