LoPy node sends join requests, and my nano gateway tries to forward it. But no sccessful join?

[jmarcelino]

@lollisoft
Well your join packet seems to be going out correctly, if you take your data

APpHAPB+1bNw7BR/5wa66QD4jBJ0lPk=

As decode it for example using https://runkit.io/avbentem/lorawan-packet-decoder/branches/master?data=APpHAPB%2B1bNw7BR%2F5wa66QD4jBJ0lPk%3D you get:

Message Type = Join Request
      AppEUI = 70B3D57EF00047FA
      DevEUI = 00E9BA06E77F14EC
    DevNonce = 8CF8
         MIC = 127494F9

Which is correct.

What you need is to check the incoming (Join Accept) response from Things Network.

Maybe on the nanogateway script try adding some debugging (printing) the data received in send_down_link and decode it via the web interface above.

[lollisoft]

Just one important question: Should the gateway get reported online after I start it up?

I have the feeling that there is something wrong with the gateway. It just sends some data to the servers, but I do not see an online state change thereof.

Is the gateway able to send it's own health messages (as a node of it's own)?

[jmarcelino]

This post is deleted!

[jmarcelino]

@lollisoft

The online indicator in TTN has been frequently broken in the past weeks, but you can try the alternative methods listed at

https://www.thethingsnetwork.org/forum/t/known-issue-gateways-show-as-not-connected-in-the-console/6527

[lollisoft]

@jmarcelino The link mentioned in that post, reports the same error as one complains.

My link to check is http://noc.thethingsnetwork.org:8085/api/v2/gateways/eui-a282f287ef724724
As of my gateway id is mentioned above, the link here is just a repeat (and I tried).

I have my firewall as a suspect to make trouble. Also my DSL router needs to forward a packet. I have therefore setup an open port to 1700 using UDP and send that to the gateway address in the same network as the DSL router.

Are the ports (sending at 1700 and ansering back over 1700) correct?

I also would setup the UDP port to point to my firewall. That way I may have a chance to see a possible answer.

[lollisoft]

The packets are sent to my firewall and then I do see these. If the packets are send to ttn, I can't see them but I also did not get any acknowledge back on the udp port 1700.

I have no more ideas...

[jmarcelino]

@lollisoft
What does your config.py on the nanogateway look like? (But remove the wifi keys)

[lollisoft]

Haha,

tried several times to setup the gateway. Wrong gateway id. Now the gateway got a Push Ack.

[zetxx]

@lollisoft https://www.youtube.com/watch?v=jL7hSx9qNjc

[berni]

I know this is an old post, but I have similar issues and after some debugging this is what I found:

1. The nanogateway gets the join request from the node using OTAA and it forwards it to TTN.

2. TTN sees the join requests and replies back to the gateway:

3. Adding some debugging I can display the data received from TTN and sent to the node using the _send_down_link function:

def _send_down_link(self, data, tmst, datarate, frequency):
        self.lora.init(mode=LoRa.LORA, frequency=frequency, bandwidth=LoRa.BW_125KHZ,
                       sf=self._dr_to_sf(datarate), preamble=8, coding_rate=LoRa.CODING_4_5,
                       tx_iq=True)
        while time.ticks_us() < tmst:
            pass
        print(binascii.hexlify(data).upper())
        self.lora_sock.send(data)

4. Decoding the returned data shows that TTN is accepting the node to join:
   https://lorawan-packet-decoder-0ta6puiniaut.runkit.sh/?data=20B6330995FA5AD1601C019F596C711FE11FF096E1C4915F94F183BEA903746F23

Assuming hex-encoded packet
20B6330995FA5AD1601C019F596C711FE11FF096E1C4915F94F183BEA903746F23

Message Type = Join Accept
    AppNonce = 0933B6
       NetID = 5AFA95
     DevAddr = 011C60D1
         MIC = 03746F23

5. However, the node keeps trying and is unable to join or takes several attempts until it is successful.

I hope this helps solving this issue...