Does deepsleep work at all

tmz

@daniel The deep sleep works! But then at one point without any error it's not entering into next deep sleep cycle instead is enter into REPL.

daniel

@tmz what you say is that after calling the go_to_sleep() the deepsleep shield doesn't put the LoPy to sleep?

tmz

@daniel Yes, executing go_to_sleep() some cycles works and than at one point it's not enter into deep sleep mode.

Do you have anything connected to P12?
Nothing connected to P12.

For debugging i was running connected over "Serial" to see what happens and for some time (cca. 5 - 20 cycles) works normally and then without errors enters into REPL.

code:

    # Setup deep sleep mode
    ds = DeepSleep()
    ds.enable_wake_on_raise('P17')
    # Some work here
    ds.go_to_sleep(60)

tmz

@daniel
I make now the execution
Deep sleep ends after 4 cycles.

LoPy on Expansion board with "DeepSleep Shield"
Firmware version: 1.7.9.b1

deepslep.py latest: https://github.com/pycom/pycom-libraries/commit/074bc7ee0181451720bbeb30d627debafc617ad8

Run 60 seconds deepsleep interval.

Output:

MicroPython v1.8.6-740-g5b756011 on 2017-08-07; LoPy with ESP32
Type "help()" for more information.
>>>
>>>
>>> ets Jun  8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
ets Jun  8 2016 00:22:57

rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff9010,len:12
ho 0 tail 12 room 4
load:0x3fff9020,len:388
load:0x40078000,len:11584
load:0x4009fb00,len:848
entry 0x4009fc9c

****DEEP SLEEP MODE****

Do sem work for 3 seconds
End work go deep sleep for 1min

Brownets Jun  8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
ets Jun  8 2016 00:22:57

rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff9010,len:12
ho 0 tail 12 room 4
load:0x3fff9020,len:388
load:0x40078000,len:11584
load:0x4009fb00,len:848
entry 0x4009fc9c

****DEEP SLEEP MODE****

Do sem work for 3 seconds
End work go deep sleep for 1min

Brownets Jun  8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
ets Jun  8 2016 00:22:57
rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff9010,len:12
ho 0 tail 12 room 4
load:0x3fff9020,len:388
load:0x40078000,len:11584
load:0x4009fb00,len:848
entry 0x4009fc9c

****DEEP SLEEP MODE****

Do sem work for 3 seconds
End work go deep sleep for 1min

Brownets Jun  8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
ets Jun  8 2016 00:22:57

rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff9010,len:12
ho 0 tail 12 room 4
load:0x3fff9020,len:388
load:0x40078000,len:11584
load:0x4009fb00,len:848
entry 0x4009fc9c

****DEEP SLEEP MODE****

Do sem work for 3 seconds
End work go deep sleep for 1min
MicroPython v1.8.6-740-g5b756011 on 2017-08-07; LoPy with ESP32
Type "help()" for more information.
>>>
>>>

daniel

@tmz Do you have a pull-down on P17? I think what is happening is that noise is waking up the deepsleep shield before it gets to turn off the LoPy completely. Please try putting an external pull-down to P17 and disabling the internall pull-up with the deepsleep library.

tmz

@daniel said in Does deepsleep work at all:

Do you have a pull-down on P17?
I have plugged the P17 and GND to have an option to wakeup (with normally close switch) and set ds.enable_wake_on_raise('P17').

Now tested "without plugging P17 with GND".
Running the example from documentation:

...
ds.enable_pullups('P17')  # can also do ds.enable_pullups(['P17', 'P18'])
ds.enable_wake_on_fall('P17') # can also do ds.enable_wake_on_fall(['P17', 'P18'])
...

With same result as before it runs 5 cycles and ends.

At home i don't have any resistor i will let you know tomorrow.

chumelnicu

@chumelnicu Hi Daniel, sorry for late update but i was in holliday until yesterday.

I did try deepsleep with new DeepSleep library and llopy behive same. After 14-15 DS cycles program stop running.

I use lopy with DS Shield powered from USB and nothing on Pin12.
Condition to wake up, is time, w-up after 10 minutes.
Do u have any ideea what is wrong?

Thx !

tmz

@daniel The result is the same. Stops after (5 - 20) cycles. How do i run in more verbose way? There is no error, it's jumps into REPL.

chumelnicu

@daniel Could you tell me how and when DeepSleep will work ? Im not only one who claim about this problem and I think is really time to clarify with your team what is happening

Thank you !

Robin

@adam_IoTK

I have the same problem with a LoPy + Deep sleep shield.
My code runs for 20-40 times and then stops. Issue reported here: https://forum.pycom.io/topic/1685/lopy-with-deep-sleep-shield-is-unstable

This is a blocker for any real world deployment.
Not having seen any useful response from the Pycom team on the forum about this issue i am considering moving to another platform to get my project finished.

daniel

Hello,

The instability has been fixed here: https://github.com/pycom/pycom-libraries/commit/ea3e22c14884671801bcd1cfe49c703bc63c7078

We are now working on reducing the deep sleep current.

Cheers,
Daniel

tmz

@daniel
Thank you! The issues seems to be fixed after this fix.
Is > 8h without interruption.

LoPy v1.7.9.b3
Expansion board (with deep sleep shield)
Fix: https://github.com/pycom/pycom-libraries/commit/ea3e22c14884671801bcd1cfe49c703bc63c7078

Robin

@daniel Seems to work for me too now.
Adding the garbage collector statements in the calling code seems to be crucial through.

johncaipa

@daniel I'm testing the deepsleep example but I get the following errors:

Traceback (most recent call last):
File "main.py", line 7, in <module>
File "/flash/lib/deepsleep.py", line 143, in get_wake_status
File "/flash/lib/deepsleep.py", line 76, in peek
IndexError: bytes index out of range

I am doing something wrong?
thanks

tmz

@johncaipa

Try the latest - https://github.com/pycom/pycom-libraries/blob/master/deepsleep/deepsleep.py

johncaipa

@tmz that is the library I'm using, and which errors are generated

Arnaud

@tmz said in Does deepsleep work at all:

https://github.com/pycom/pycom-libraries/blob/master/deepsleep/deepsleep.py

Just tried the deepsleep example on Sipy 1.0 - Pytrack 1.0 with latest deepsleep.py and after firmware upgrade to 1.7.9b3 and got the same error than John.

I understood that Pytrack serves as deepsleep shield.
All this deepsleep troubles merged with lack of documentation is really frustrating...

daniel

@Arnaud with pytrack or pysense simply use their own libraries which also provide the deepsleep functionality:

https://github.com/pycom/pycom-libraries/tree/master/pytrack

Arnaud

Nice to hear that! Please help us with a bit more explicit documentation. You might be aware of this now based on the comments, you're building up hours of frustration which is not was intended at first I'm sure with the beautiful specs of your products.

BTW, I think deepsleep example lacks an import deepsleep for constants.

Arnaud

@daniel I've tried the latest pytrack lib for deepsleep with very simple main.py:
from pytrack import Pytrack

Explore Pybytes | Official Documentation | Report a Firmware Bug/Issue | GitHub

Does deepsleep work at all

Some job

Pycom on Twitter