Welcome to the Pycom forum Forum
    • \[\[global:header.categories\]\]
    • \[\[global:header.recent\]\]
    • \[\[global:header.tags\]\]
    • \[\[global:header.popular\]\]
    • Login

    Explore Pybytes | Official Documentation | Report a Firmware Bug/Issue | GitHub

    LoRaWAN TTN Uplinks Ok, no Downlinks. Channel issue? Help! ;)

    Scheduled Pinned Locked Moved LoPy
    lopy4lorawanttn
    20 Posts 4 Posters 3.2k Views 5 Watching
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • A Offline
      AidanRTaylor @jmarcelino
      last edited by

      @jmarcelino Hi jmarcelino - thanks for the reply, I will try cutting back the code in that case (I guess I can just comment out the channel set up) but I am pretty sure I had no luck until I set that up.

      The Data panel in console is showing that following an Uplink, the Gateway responds on Port 1 Confirmed with bytes 0x04 0x05 0x06

      I set this up but again, not really sure how to configure it

      A 1 Reply Last reply Reply Quote 1
      • A Offline
        AidanRTaylor @AidanRTaylor
        last edited by

        Yep, as it turns out there is no need to configure the channels after all - still no downlinks though.

        J 1 Reply Last reply Reply Quote 1
        • J Offline
          jmarcelino @AidanRTaylor
          last edited by

          @aidanrtaylor
          Can you post a screenshot of your TTN console Data panel please showing the uplinks/donwlinks?

          I've upvoted your posts so you should be able to now.

          Thanks

          1 Reply Last reply Reply Quote 1
          • A Offline
            AidanRTaylor
            last edited by

            Hey I got some bits! It's pretty intermittent though, the device is still missing the majority of downlinks, that's the first successful packet I have seen though!

            0_1527762892728_ttnconsole.png

            1 Reply Last reply Reply Quote 0
            • A Offline
              AidanRTaylor
              last edited by

              It's also missing most Uplinks now, whereas it was catching most with the previous code

              J 1 Reply Last reply Reply Quote 0
              • J Offline
                jmarcelino @AidanRTaylor
                last edited by

                @aidanrtaylor
                Maybe the gateway you're using or have access to is single channel?

                Expand the received packets on the Data tab and look at the frequency used. If they're all on the same frequency then your gateway is probably single channel.

                A 1 Reply Last reply Reply Quote 1
                • A Offline
                  AidanRTaylor @jmarcelino
                  last edited by

                  @jmarcelino I have access to the gateway - is it something I can check on there?

                  1 Reply Last reply Reply Quote 0
                  • A Offline
                    AidanRTaylor
                    last edited by AidanRTaylor

                    I can't consistently get packets up or down now that I have modified the code :( The original code only gets consistent uplinks. Is there anything else I have missed or 'fudged'?

                    I haven't been able to get another Downlink to expand.

                    # LoPy4_files/main.py
                    
                    import time
                    from network import LoRa
                    import binascii
                    import pycom
                    from machine import Pin
                    import socket
                    import struct # no idea what this does - need to read up on it
                    
                    # Configure IO Pins:
                    configPin = Pin('P21', Pin.IN, Pin.PULL_UP) # Pull low to exit to REPL
                    LoRaPin = Pin('P22', Pin.IN, Pin.PULL_UP) # Pull low to enable LoRa
                    
                    #Set AppEUI and AppKey - use your values from the device settings --> https://console.thethingsnetwork.org/
                    dev_eui = binascii.unhexlify('***')
                    app_eui = binascii.unhexlify('***')
                    app_key = binascii.unhexlify('***')
                    
                    # initial read from IO pins:
                    config = configPin()
                    radio = LoRaPin()
                    
                    # In 'config mode' exit to the REPL, and print the LoRa DevEUI:
                    if not config:
                        print('Config Mode')
                    
                        lora = LoRa()
                        print("DevEUI: %s" % (binascii.hexlify(lora.mac()).decode('ascii')))
                    
                    # Otherwise, we probably want to activate LoRa:
                    if not radio:
                        pycom.rgbled(0x7f0000) #red
                    
                        lora = LoRa(mode=LoRa.LORAWAN, region = LoRa.EU868)
                    
                        # # Remove all the non-default channels
                        # for i in range(3, 16):
                        #     lora.remove_channel(i)
                        # print('Removed default channels')
                        # time.sleep(1)
                        #
                        # # Set EU ISM 868 channel plan for TTN Europe
                        # lora.add_channel(0, frequency=868100000, dr_min=0, dr_max=5)
                        # lora.add_channel(1, frequency=868300000, dr_min=0, dr_max=5)
                        # lora.add_channel(2, frequency=868500000, dr_min=0, dr_max=5)
                        # lora.add_channel(3, frequency=867100000, dr_min=0, dr_max=5)
                        # lora.add_channel(4, frequency=867300000, dr_min=0, dr_max=5)
                        # lora.add_channel(5, frequency=867500000, dr_min=0, dr_max=5)
                        # lora.add_channel(6, frequency=867700000, dr_min=0, dr_max=5)
                        # lora.add_channel(7, frequency=867900000, dr_min=0, dr_max=5)
                        #
                        # print('EU channels set')
                        time.sleep(1)
                    
                        #Join TTN Network via OTAA
                        lora.join(activation=LoRa.OTAA, auth=(dev_eui, app_eui, app_key), timeout=0, dr=0)
                    
                        # wait until the module has joined the network
                        print('Trying to join TTN Network...')
                        while not lora.has_joined():
                            pycom.rgbled(0x7f7f00) #yellow
                            time.sleep(5)
                            print('...')
                            pass
                    
                        print('Network joined')
                        pycom.rgbled(0x009999) #teal
                    
                    
                        # Now let's send some data...
                        # create a LoRa socket
                        s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)
                    
                        # set the LoRaWAN data rate
                        s.setsockopt(socket.SOL_LORA, socket.SO_DR, 5)
                    
                        while lora.has_joined():
                            print('Sending some bits:', bytes([0x01, 0x02, 0x03]))
                            # make the socket blocking
                            s.setblocking(True)
                            s.send(bytes([0x01, 0x02, 0x03]))
                    
                            time.sleep(0.5)
                    
                            print('Listening for bits:')
                            s.setblocking(False)
                            data = s.recv(64)
                            print(data)
                    
                            time.sleep(30)
                    
                        print('Connection lost')
                    
                    J 1 Reply Last reply Reply Quote 0
                    • J Offline
                      jmarcelino @AidanRTaylor
                      last edited by

                      @aidanrtaylor
                      Can you look at the received frequencies on the TTN console?

                      What is your gateway?

                      A 1 Reply Last reply Reply Quote 1
                      • A Offline
                        AidanRTaylor @jmarcelino
                        last edited by

                        @jmarcelino Hey - I am getting successful downlinks now. I reverted back to my original code, but I changed the parameters for socket.setsockopt, I changed the last field (data rate?) from 5 to 1 and I am getting consistent robust results now.

                        In answer to your questions - the Gateway doesn't belong to me but the owner gave me access to it for troubleshooting - I'm not sure which parameters would be relevant to you.

                        Anyway, on the console I can't get any useful information from the successful downlinks as far as I can tell. But the metadata on the received Uplinks is showing different frequencies for each result - so I guess we are good there.

                        Onwards and upwards! For reference this is the code I have ended up with:

                        # LoPy4_files/main.py
                        
                        import time
                        from network import LoRa
                        import binascii
                        import pycom
                        from machine import Pin
                        import socket
                        import struct # no idea what this does - need to read up on it
                        
                        # Configure IO Pins:
                        configPin = Pin('P21', Pin.IN, Pin.PULL_UP) # Pull low to exit to REPL
                        LoRaPin = Pin('P22', Pin.IN, Pin.PULL_UP) # Pull low to enable LoRa
                        
                        #Set AppEUI and AppKey - use your values from the device settings --> https://console.thethingsnetwork.org/
                        dev_eui = binascii.unhexlify('***')
                        app_eui = binascii.unhexlify('***')
                        app_key = binascii.unhexlify('***')
                        
                        # initial read from IO pins:
                        config = configPin()
                        radio = LoRaPin()
                        
                        # In 'config mode' exit to the REPL, and print the LoRa DevEUI:
                        if not config:
                            print('Config Mode')
                        
                            lora = LoRa()
                            print("DevEUI: %s" % (binascii.hexlify(lora.mac()).decode('ascii')))
                        
                        # Otherwise, we probably want to activate LoRa:
                        if not radio:
                            pycom.rgbled(0x7f0000) #red
                        
                            lora = LoRa(mode=LoRa.LORAWAN, region = LoRa.EU868)
                        
                            # Remove all the non-default channels
                            for i in range(3, 16):
                                lora.remove_channel(i)
                            print('Removed default channels')
                            time.sleep(1)
                        
                            # Set EU ISM 868 channel plan for TTN Europe
                            lora.add_channel(0, frequency=868100000, dr_min=0, dr_max=5)
                            lora.add_channel(1, frequency=868300000, dr_min=0, dr_max=5)
                            lora.add_channel(2, frequency=868500000, dr_min=0, dr_max=5)
                            lora.add_channel(3, frequency=867100000, dr_min=0, dr_max=5)
                            lora.add_channel(4, frequency=867300000, dr_min=0, dr_max=5)
                            lora.add_channel(5, frequency=867500000, dr_min=0, dr_max=5)
                            lora.add_channel(6, frequency=867700000, dr_min=0, dr_max=5)
                            lora.add_channel(7, frequency=867900000, dr_min=0, dr_max=5)
                        
                            print('EU channels set')
                            time.sleep(1)
                        
                            #Join TTN Network via OTAA
                            lora.join(activation=LoRa.OTAA, auth=(dev_eui, app_eui, app_key), timeout=0, dr=0)
                        
                            # wait until the module has joined the network
                            print('Trying to join TTN Network...')
                            while not lora.has_joined():
                                pycom.rgbled(0x7f7f00) #yellow
                                time.sleep(5)
                                print('...')
                                pass
                        
                            print('Network joined')
                            pycom.rgbled(0x009999) #teal
                        
                        
                            # Now let's send some data...
                            # create a LoRa socket
                            s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)
                        
                            # set the LoRaWAN data rate
                            s.setsockopt(socket.SOL_LORA, socket.SO_DR, 1)
                        
                            while lora.has_joined():
                                print('Sending some bits:', bytes([0x01, 0x02, 0x03]))
                                # make the socket blocking
                                s.setblocking(True)
                                s.send(bytes([0x01, 0x02, 0x03]))
                        
                                time.sleep(0.5)
                        
                                print('Listening for bits:')
                                s.setblocking(False)
                                data = s.recv(64)
                                print(data)
                        
                                time.sleep(30)
                        
                            print('Connection lost')
                        
                        1 Reply Last reply Reply Quote 0
                        • Charly86C Offline
                          Charly86 @jmarcelino
                          last edited by

                          @jmarcelino if you use another backend with OTAA, how can we check in lopy code if the GW has sent the other channels? I programmed them on the GW but want to be sure they were deployed to the end device ;-)

                          J 1 Reply Last reply Reply Quote 0
                          • J Offline
                            jmarcelino @Charly86
                            last edited by jmarcelino

                            @charly86
                            If you set (add_channel) the first three channels (EU868 only) to the same, but alternate, frequency you can verify if the gateway is picking that frequency up.

                            lora.add_channel(0, frequency=FREQUENCY, dr_min=0, dr_max=5)
                            lora.add_channel(1, frequency=FREQUENCY, dr_min=0, dr_max=5)
                            lora.add_channel(2, frequency=FREQUENCY, dr_min=0, dr_max=5)

                            Is that you mean? Or do you mean reassigning the RX2 window?

                            Charly86C 1 Reply Last reply Reply Quote 0
                            • Charly86C Offline
                              Charly86 @jmarcelino
                              last edited by Charly86

                              @jmarcelino thanks
                              In fact, I mean you said for TTN, OTAA download all usable channels send by the backend.

                              But I want to be sure my LoPy received it and can use the 8 instead of forcing adding manually the 5 others on the LoPy Code
                              But I can see in GW log if is use the other frequencies

                              J robert-hhR 2 Replies Last reply Reply Quote 0
                              • J Offline
                                jmarcelino @Charly86
                                last edited by jmarcelino

                                @charly86
                                Oh OK so if you do more than 3 sends in quick succession it should use the extra channels

                                Set it with a low DR to make sure, i.e.: s.setsockopt(socket.SOL_LORA, socket.SO_DR, 0)

                                There isn't a function to check the current channel map in use so I think this is the simplest way.

                                Charly86C 1 Reply Last reply Reply Quote 0
                                • robert-hhR Offline
                                  robert-hh @Charly86
                                  last edited by

                                  @charly86 I see a problem at the moment with TTN, in that uplink packets using TCP show up at the Data tab of the console very late, wheres UDP packets pop up immediately. If the gateway is using TCP, the downlink messages may be sent too late,

                                  1 Reply Last reply Reply Quote 1
                                  • Charly86C Offline
                                    Charly86 @jmarcelino
                                    last edited by

                                    @jmarcelino oh I see, thanks.
                                    While writing, if after join I remove channel 0, 1 and 2 it should use the other? Should works for testing?

                                    J 1 Reply Last reply Reply Quote 0
                                    • J Offline
                                      jmarcelino @Charly86
                                      last edited by

                                      @charly86
                                      Because those are mandatory channels you can't remove the 3 default channels in EU868, you can only change their frequency (but the frequency can be the same for all three)

                                      Charly86C 1 Reply Last reply Reply Quote 1
                                      • Charly86C Offline
                                        Charly86 @jmarcelino
                                        last edited by Charly86

                                        @jmarcelino Hey, got it, thanks
                                        As you suggested I'll write a prog to quick send data and looks on my backend for frequencies of received packet ;-)
                                        Look like the faster way

                                        1 Reply Last reply Reply Quote 1

                                        Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                        Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                        With your input, this post could be even better 💗

                                        Register Login
                                        • 1 / 1
                                        • First post
                                          Last post

                                        Pycom on Twitter

                                        Pycom