Arduino sends data seriell, how to get them into WiPy ? **SOLVED**

[Hotzenwald]

@robert-hh thanks for your fast answer. I use a couple of shields at the arduino R3 and will not be able to convert this for WiPy.

[Hotzenwald]

@RobTuDelft had a look at i2C and think this is what i should try. Thanks

[Hotzenwald]

@RobTuDelft sorry, i am not that familiar with WiPy. I get this Error:
ImportError: cannot import name I2C
This is just example code i found

rom network import WLAN
import time
import socket
from machine import I2C
import machine
#configure the I2C bus
i2c = I2C(0, I2C.MASTER, baudrate=100000)
i2c.scan() # returns list of slave addresses
print('I2C ist aktiviert')

Do i have to prepare something else ?

[robert-hh]

I tested that code snippet on my LoPy and it works.
What kind of WiPy and MP version are you using?
Look at the output of:

import uos
uos.uname()

[Hotzenwald]

@robert-hh Thanks. Managed to do a firmware update and now works.
(sysname='WiPy', nodename='WiPy', release='1.6.8.b1', version='v1.8.6-504-gff1098f6 on 2017-03-13', machine='WiPy with ESP32')

[vruizvil]

@Hotzenwald
My code to read Arduino Serial port, works fine for me.

import machine

#initialize serial port on P3 P4 (Tx Rx)
uart1=machine.UART(1, 115200)

def serialrecv(uartport):
  #read the length of the data, letter by letter until we reach EOL
  length_str = ''
  char = uartport.read(1)
  while char.decode() != '\r':
     length_str += char.decode()
     char = uartport.read(1) 
  return length_str

while (True):
    #read the serial message
    serialdata=serialrecv(uart1)
    print(serialdata)

[livius]

@Hotzenwald
woow 1.6.8?
@daniel i do not see any info about this?

[vruizvil]

@Hotzenwald Hi!!
I use Lopy. In my project, connecting from lopy P3(TX1) to arduino PIN0(RX) and lopy P4(RX1) to arduino uno PIN1(TX) it works. You need initialize uart1 whit the same baud rate than arduino.
Here my arduino code to read DHT11 temperature sensor.

#ARDUINO CODE TO READ DHT11 VALUES AND SEND IT TO SERIAL ON JSON FORMAT
include <SimpleDHT.h>
// for DHT11, 
//      VCC: 5V or 3V
//      GND: GND
//      DATA: 2
int pinDHT11 = 2;
SimpleDHT11 dht11;

void setup() {
  Serial.begin(115200);
}

void loop() {
   byte temperature = 0;
  byte humidity = 0;
  if (dht11.read(pinDHT11, &temperature, &humidity, NULL)) {
    Serial.print("Read DHT11 failed.");
    return;
  }
  Serial.print("{\"T\":"); Serial.print((int)temperature); Serial.print(",");
  Serial.print("\"H\":"); Serial.print((int)humidity); Serial.println("}");
  
  // DHT11 sampling rate is 2HZ.
  delay(2000);

[RobTuDelft]

I think indeed a communication through UART is the best option. Also see the tutorial I wrote here: https://forum.pycom.io/topic/978/lopy-arduino-serial-communication.

Hope that helps.

[Hotzenwald]

solved.
The problems i had has been level shifter dependend. I used another one and UART started to work.
Another trap has been a misunderstanding in PIN numbering and PIN layout. When i just looked at WiPy pinout without paying attention to expansion board i noticed, that i used the wrong PINs. Now i count from left side, starting with 0 and figured out which PINs i do have to use.
Now it works like a charm.
Thanks for all your help !