Has anyone successfully used lora.nvram_save() and restore?

bmarkus

@johncaipa said in Has anyone successfully used lora.nvram_save() and restore?:

@jalperin @jmarcelino works but the counter is restarted on each send, this value is not stored?

Unfortunately it is not possible to get or set your own FCnt value, otherwise it would be possible to handle in your code. Just one of the several missing LoRa/LoRaWAN functions.

johncaipa

@bmarkus in the documentation says that this value is saved, then I do not know what would be the problem, because in each sending after waking up the packet counters is always in 1 on TTN.
"lora.nvram_save()
Save the LoRaWAN state (joined status, network keys, packet counters, etc) in non-volatile memory in order to be able to restore the state when coming out of deepsleep or a power cycle."

bmarkus

@johncaipa said in Has anyone successfully used lora.nvram_save() and restore?:

@bmarkus in the documentation says that this value is saved, then I do not know what would be the problem, because in each sending after waking up the packet counters is always in 1 on TTN.
"lora.nvram_save()
Save the LoRaWAN state (joined status, network keys, packet counters, etc) in non-volatile memory in order to be able to restore the state when coming out of deepsleep or a power cycle."

Do you create a new instance when coming out? It resets the counter.

johncaipa

@bmarkus this is the example code I'm testing, based on which share @jalperin, I'm missing something?

from network import LoRa
import struct
import binascii
import time
import math
import pycom
import socket
from pysense import Pysense

py = Pysense()
loraSaved = pycom.nvs_get('loraSaved')
print(loraSaved)
if not loraSaved:
lora = LoRa(mode=LoRa.LORAWAN)
freq = 902300000
for channel in range(0, 72):
lora.remove_channel(channel)
for chan in range(0, 8):
lora.add_channel(chan, frequency=freq, dr_min=0, dr_max=3)

dev_addr = struct.unpack(">l", binascii.unhexlify('************'.replace(' ','')))[0]
nwk_swkey = binascii.unhexlify('************ 89 F1 74 79 40'.replace(' ',''))
app_swkey = binascii.unhexlify('************ 3A AA BD E8 A9'.replace(' ',''))
lora.join(activation=LoRa.ABP, auth=(dev_addr, nwk_swkey, app_swkey))
while not lora.has_joined():
    machine.idle()
s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)
s.setsockopt(socket.SOL_LORA, socket.SO_DR, 3)
s.bind(3) #select the port number
s.setblocking(False)
s.send('LoRa Up')
time.sleep(2)
lora.nvram_save()
pycom.nvs_set('loraSaved', 1)
py.setup_sleep(60)
py.go_to_sleep()

else:
lora = LoRa(mode=LoRa.LORAWAN)
lora.nvram_restore()
freq = 902300000
for channel in range(0, 72):
lora.remove_channel(channel)
for chan in range(0, 8):
lora.add_channel(chan, frequency=freq, dr_min=0, dr_max=3)
s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)
s.setsockopt(socket.SOL_LORA, socket.SO_DR, 3)
s.bind(3) #select the port number
s.setblocking(False)
s.send('LoRa Restored')
time.sleep(2)
lora.nvram_save()
#pycom.nvs_set('loraSaved', 0) # reset for next test
py.setup_sleep(60)
py.go_to_sleep()

rloro338

I am trying to use lora.nvram_save() and lora.nvram_restore() and not works. I set all parameters (LoRaWAN, adr = True, app_eui, app_key and channel configuration) the first time that I boot the device and send a message Loriot server receive it. Then device go to deepsleep for 5 seconds and restore the join state. If I look the state with lora.has_joined() return True value, but when I trying to send the message it isn't received by the gateway.

It is curious because when I use the node directly with a command line in Putty the restore and save comands works fine.

What I am doing wrong??

johncaipa

@rloro338 I made the following changes to my code and now it works correctly:

list item make sure the socket is blocking ( s.setblocking(True) )
list item add a time.sleep(2) after sending, before saving and going to deep sleep.

Bismarck501

@jmarcelino Hello, I have read your suggestion carefully and tried in my project. But there was some issues about this solution.
My device consists of FiPy+pysense, and I connected to TTN via OTAA. My code with lora,nvram_save() and restore() is:

# pysense sensor part
from pysense import Pysense
from LTR329ALS01 import LTR329ALS01
from LIS2HH12 import LIS2HH12

# FiPy part
from network import LoRa
import socket
import time
import pycom
import ubinascii
import machine

# pysense machine part
from machine import RTC
from machine import SD
import os

from network import WLAN, Bluetooth,LTE

# set parameters for sensor function
py = Pysense()
lt = LTR329ALS01(py)  # only use light sensor


loraSaved = pycom.nvs_get('loraSaved')  # if join already, it is int 3; or it will be None
#-------------------------------- if already join -------------------------------------#
if (loraSaved == 11):

    lora = LoRa(mode=LoRa.LORAWAN, region=LoRa.EU868)

    lora.nvram_restore()
    #--------- Remove default channels ----------#
    for index in range(0, 15):
        lora.remove_channel(index)
    lora.add_channel(3, frequency=867100000, dr_min=0, dr_max=5)
    lora.add_channel(4, frequency=867300000, dr_min=0, dr_max=5)
    lora.add_channel(5, frequency=867500000, dr_min=0, dr_max=5)
    lora.add_channel(6, frequency=867700000, dr_min=0, dr_max=5)
    lora.add_channel(7, frequency=867900000, dr_min=0, dr_max=5)

    lora.add_channel(8, frequency=868100000, dr_min=0, dr_max=5)
    lora.add_channel(9, frequency=868300000, dr_min=0, dr_max=5)
    lora.add_channel(10, frequency=868500000, dr_min=0, dr_max=5)
    lora.add_channel(11, frequency=868700000, dr_min=0, dr_max=5)
    lora.add_channel(12, frequency=868900000, dr_min=0, dr_max=5)

    lora.add_channel(13, frequency=869100000, dr_min=0, dr_max=5)
    lora.add_channel(14, frequency=869300000, dr_min=0, dr_max=5)
    lora.add_channel(15, frequency=869500000, dr_min=0, dr_max=5)

    print("Join already")
    #--------------------------------------------------------------------------------#
    #						Set LoRa parameters
    # create a LoRa socket
    s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)
    # set the LoRaWAN data rate
    s.setsockopt(socket.SOL_LORA, socket.SO_DR, 5)

    #---------- Send uplink & Stroe uplink data ----------------#    
    uplink_payload = ("Light: " + str(lt.light()))
    s.setblocking(True)
    s.send(uplink_payload)
    lora.nvram_save()
    print("send finish")
    
    #--------- Receive downlink & Stroe downlink data ----------#
    s.setblocking(False)
    downlink_message = s.recv(64) # bytes form     and     n is typically < 64 bytes
    time.sleep(1)
    print(downlink_message)
    print(type(downlink_message))
    print("Receive finish")

    #----------- Jugde whether there is a downlink -------------#
    if downlink_message == b'':
        print("There is no downlink")
    else:
        downlink_payload = downlink_message.decode('ascii') # string form
        print("Downlink message: " + downlink_payload)
        #-------- Judge downlink message & operate -------------#
        if downlink_message == b'2': # if ==2, it will light green for 5 seconds
            print("Hi, Green!")
            pycom.rgbled(0x007f00) # green
            time.sleep(3)
        if downlink_message == b'4': # if ==4, it will light yellow for 5 seconds
            print("Hi, Yellow!")
            pycom.rgbled(0x7f7f00) # yellow
            time.sleep(3)
    print("####################################")
    print("\n")

#-------------------------------- if never join before -------------------------------------#
else:
    print("Firstly join")
    #--------------------------------------------------------------------------------#
    # 					Initialise LoRa in LORAWAN mode.
    lora = LoRa(mode=LoRa.LORAWAN, region=LoRa.EU868)
    #--------------------------------------------------------------------------------#
    #				Set OTAA mode and connect with the gateway
    # create an OTAA authentication parameters
    app_eui = ubinascii.unhexlify('70B3D57ED0013E78')
    app_key = ubinascii.unhexlify('5D87FAB0BC66A45FB0DA07453ED2BC2B')
    # join a network using OTAA (Over the Air Activation)
    lora.join(activation=LoRa.OTAA, auth=(app_eui, app_key), timeout=0)
    # wait until the module has joined the network
    while not lora.has_joined():
        time.sleep(2.5)
        print('Not yet joined...')
    # join in
    print('Successfully join in!')
    #--------------------------------------------------------------------------------#
    #						Set LoRa parameters
    # create a LoRa socket
    s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)
    # set the LoRaWAN data rate
    s.setsockopt(socket.SOL_LORA, socket.SO_DR, 5)

    #---------- Send uplink & Stroe uplink data ----------------#
    uplink_payload = ("Light: " + str(lt.light()))
    s.setblocking(True)
    s.send(uplink_payload)
    lora.nvram_save()

    #--------- Receive downlink & Stroe downlink data ----------#
    s.setblocking(False)
    downlink_message = s.recv(64) # bytes form     and     n is typically < 64 bytes
    #time.sleep(1)
    print(downlink_message)
    print(type(downlink_message))

    #----------- Jugde whether there is a downlink -------------#
    if downlink_message == b'':
        print("There is no downlink")
    else:
        downlink_payload = downlink_message.decode('ascii') # string form
        print("Downlink message: " + downlink_payload)

        #-------- Judge downlink message & operate -------------#
        if downlink_message == b'2': # if ==2, it will light green for 5 seconds
            print("Hi, Green!")
            pycom.rgbled(0x007f00) # green
            time.sleep(3)
        if downlink_message == b'4': # if ==4, it will light yellow for 5 seconds
            print("Hi, Yellow!")
            pycom.rgbled(0x7f7f00) # yellow
            time.sleep(3)
    print("####################################")
    print("\n")
    #---------- store in flush to judge next time ----------------#
    pycom.nvs_set('loraSaved', 11)  
# time sleep
py.setup_sleep(9)   # setup a 9 seconds sleep time
py.go_to_sleep()

And it can work well. However, after one day, when I tried again, there would be an issue when running code at line 65:

    s.send(uplink_payload)

Where I was wrong? Thanks for giving me some advice!

jcaron

@Bismarck501 You should factorise your code a lot, it would make things a lot easier to maintain.

You shouldn't rely on an additional NVRAM variable to determine your LoRaWAN state.

Instead, just call nvram_restore, then has_joined. If not true, you need to join. Otherwise, you can go ahead and send/receive.

Also, I would call nvram_save after any interaction with the LoRaWAN stack is finished including the recv part. Not sure it currently causes any issues, but it's better to be consistent.

Bismarck501

@jcaron Thanks for responsing so quick! I have tried your suggestion and it works now. And I will experiment further to eusure the stability. Now the code is:

# pysense sensor part
from pysense import Pysense
from LTR329ALS01 import LTR329ALS01
from LIS2HH12 import LIS2HH12

# FiPy part
from network import LoRa
import socket
import time
import pycom
import ubinascii
import machine

# pysense machine part
from machine import RTC
from machine import SD
import os

from network import WLAN, Bluetooth,LTE

# set parameters for sensor function
py = Pysense()
lt = LTR329ALS01(py)  # only use light sensor

lora = LoRa(mode=LoRa.LORAWAN, region=LoRa.EU868)   # itialise LoRa in LORAWAN mode.
lora.nvram_restore()
#-------------------------------- if never join before -------------------------------------#
if not lora.has_joined():
    print("Firstly join")
    #-------------------- use OTAA to connect with TTN ------------------------------#
    app_eui = ubinascii.unhexlify('70B3D57ED0013E78')
    app_key = ubinascii.unhexlify('5D87FAB0BC66A45FB0DA07453ED2BC2B')
    lora.join(activation=LoRa.OTAA, auth=(app_eui, app_key), timeout=0) # join a network using OTAA (Over the Air Activation)
    while not lora.has_joined():    # wait until the module has joined the network
        time.sleep(2.5)
        print('Not yet joined...')
    # join in
    print('Successfully join in!')

    #---------- Set LoRa parameters ----------------#
    # create a LoRa socket
    s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)
    # set the LoRaWAN data rate
    s.setsockopt(socket.SOL_LORA, socket.SO_DR, 5)

    #---------- Send uplink & Stroe uplink data ----------------#
    uplink_payload = ("Light: " + str(lt.light()))
    s.setblocking(True)
    s.send(uplink_payload)

    #--------- Receive downlink & Stroe downlink data ----------#
    s.setblocking(False)
    downlink_message = s.recv(64) # bytes form     and     n is typically < 64 bytes
    #time.sleep(1)
    print(downlink_message)
    print(type(downlink_message))
    lora.nvram_save()   # store in flush to judge next time

    #----------- Jugde whether there is a downlink -------------#
    if downlink_message == b'':
        print("There is no downlink")
    else:
        downlink_payload = downlink_message.decode('ascii') # string form
        print("Downlink message: " + downlink_payload)
        #-------- Judge downlink message & operate -------------#
        if downlink_message == b'2': # if ==2, it will light green for 5 seconds
            print("Hi, Green!")
            pycom.heartbeat(False)
            pycom.rgbled(0x007f00) # green
            time.sleep(3)
            pycom.heartbeat(True)
        if downlink_message == b'4': # if ==4, it will light yellow for 5 seconds
            print("Hi, Yellow!")
            pycom.heartbeat(False)
            pycom.rgbled(0x7f7f00) # yellow
            time.sleep(3)
            pycom.heartbeat(True)
    print("####################################")
    print("\n")

#-------------------------------- if already join -------------------------------------#
else:
    '''
    #--------- Remove default channels ----------#
    for index in range(0, 15):
        lora.remove_channel(index)
    lora.add_channel(3, frequency=867100000, dr_min=0, dr_max=5)
    lora.add_channel(4, frequency=867300000, dr_min=0, dr_max=5)
    lora.add_channel(5, frequency=867500000, dr_min=0, dr_max=5)
    lora.add_channel(6, frequency=867700000, dr_min=0, dr_max=5)
    lora.add_channel(7, frequency=867900000, dr_min=0, dr_max=5)

    lora.add_channel(8, frequency=868100000, dr_min=0, dr_max=5)
    lora.add_channel(9, frequency=868300000, dr_min=0, dr_max=5)
    lora.add_channel(10, frequency=868500000, dr_min=0, dr_max=5)
    lora.add_channel(11, frequency=868700000, dr_min=0, dr_max=5)
    lora.add_channel(12, frequency=868900000, dr_min=0, dr_max=5)

    lora.add_channel(13, frequency=869100000, dr_min=0, dr_max=5)
    lora.add_channel(14, frequency=869300000, dr_min=0, dr_max=5)
    lora.add_channel(15, frequency=869500000, dr_min=0, dr_max=5)
    '''
    print("Join already")
    #---------------------------Set LoRa parameters-------------------------------------#
    # create a LoRa socket
    s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)
    # set the LoRaWAN data rate
    s.setsockopt(socket.SOL_LORA, socket.SO_DR, 5)

    #---------- Send uplink & Stroe uplink data ----------------#
    uplink_payload = ("Light: " + str(lt.light()))
    s.setblocking(True)
    s.send(uplink_payload)
    print("send finish")

    #--------- Receive downlink & Stroe downlink data ----------#
    s.setblocking(False)
    downlink_message = s.recv(64) # bytes form     and     n is typically < 64 bytes
    time.sleep(1)
    print(downlink_message)
    print(type(downlink_message))
    lora.nvram_save()
    print("Receive finish")

    #----------- Jugde whether there is a downlink -------------#
    if downlink_message == b'':
        print("There is no downlink")
    else:
        downlink_payload = downlink_message.decode('ascii') # string form
        print("Downlink message: " + downlink_payload)

        #-------- Judge downlink message & operate -------------#
        if downlink_message == b'2': # if ==2, it will light green for 5 seconds
            print("Hi, Green!")
            pycom.heartbeat(False)
            pycom.rgbled(0x007f00) # green
            time.sleep(3)
            pycom.heartbeat(True)
        if downlink_message == b'4': # if ==4, it will light yellow for 5 seconds
            print("Hi, Yellow!")
            pycom.heartbeat(False)
            pycom.rgbled(0x7f7f00) # yellow
            time.sleep(3)
            pycom.heartbeat(True)
    print("####################################")
    print("\n")

print("Deep sleep begin!")
# time sleep
py.setup_sleep(9)   # setup a 10 seconds sleep time
py.go_to_sleep()
#machine.deepsleep(9000)  # machine.deepsleep([milli_sec])

Thanks a lot!

Bismarck501

@jcaron The issue has been worked out and it works quite well now! Thanks a lot!

Explore Pybytes | Official Documentation | Report a Firmware Bug/Issue | GitHub

Has anyone successfully used lora.nvram_save() and restore?

Pycom on Twitter