Using PyCom boards with Arduino IDE

[Lonefish]

@mattt I never even had an OK back. Did you use the exact same code?

[mattt]

@Lonefish I tried using that code and the code in this pull request against the TinyGSM library, same result. Almost like the modem is locked until it receives a certain command.

[mattt]

I did have to add #define SerialAT Serial2
@Lonefish said in Using PyCom boards with Arduino IDE:

Did you use the exact same code

[BorbonJuggler]

Have anyone managed to do it with a Gpy ?, I have been trying without success

I am defining the UART pins as :

#define LTE_TX    23
#define LTE_RTS   18
#define LTE_RX    5
#define LTE_CTS   19

[Lonefish]

@mattt said in Using PyCom boards with Arduino IDE:

I did have to add #define SerialAT Serial2

That seemed to work indeed! Sending AT+CSQ replied with 99,99 which is no connection. Haven't tried it any further, but it's more than I had a few months ago ;) Thanks!

EDIT : There was no antenna connected nor was there a SIM inserted, so the 99,99 is logical.

[Volodymyr]

@Lonefish I'm wondering if you got this working ;)
I have updated the OP use the Serial2.

[Lonefish]

@Volodymyr I'm restarting my efforts to get this working again. Have been jumping from POC to POC. But we're switching to esp-idf instead of Arduino. Although, once it's working in esp-idf, it'd be an easy port to arduino back probably.

ATM I'm still at the "having communication" part, no actual internet connection yet, but just started working on it again.

[Lonefish]

I'm using this library at the moment, I can attach and connect to the network, but my efforts fail when I want to do some actual calls to servers. I don't seem to have http-traffic:

https://github.com/vshymanskyy/TinyGSM

[JFarque]

@Lonefish Ever get TinyGSM working? I need to sent CoAP UDP messages with it. I've used TinyGSM with other Arduino computers on standard ublox cell modules but new to narrow band.

[Kinnay21]

@Lonefish
Hello, did you finally able to use TinyGSM with FiPy or GPy in order to call servers?

[Clemens]

Would be also interested to use FiPy or GPy with TinyGSM for Arduino

[pottendo pottendo]

@Clemens said in Using PyCom boards with Arduino IDE:

Would be also interested to use FiPy or GPy with TinyGSM for Arduino

hi, you may look here: https://github.com/vshymanskyy/TinyGSM/issues/579
bye, pottendo

[Jeroen Jager]

I'm getting this error whenever I try to compile anything for the GPy:

[15975] Error loading Python lib '/var/folders/57/hyd6ntr1233_x_brscxdp8480000gn/T/_MEI7xbrkg/libpython3.8.dylib': dlopen: dlopen(/var/folders/57/hyd6ntr1233_x_brscxdp8480000gn/T/_MEI7xbrkg/libpython3.8.dylib, 10): Symbol not found: ____chkstk_darwin
  Referenced from: /var/folders/57/hyd6ntr1233_x_brscxdp8480000gn/T/_MEI7xbrkg/libintl.8.dylib
  Expected in: /usr/lib/libSystem.B.dylib
 in /var/folders/57/hyd6ntr1233_x_brscxdp8480000gn/T/_MEI7xbrkg/libintl.8.dylib

I have just re-installed Python 3.9.
Anyone know how to fix this?