Firmware update, not possible on either windows or mac osx...

[soren]

@jmarcelino Hey, OK so I think I got serial working now, but I still can't sync my project from pymakr... just keeps saying "syncing failed".. is this because there is already bootleader on the lopy? remember, I can't get into ftp because I tried changing wlan password which didn't work and now I can't connect to it.

[robert-hh]

@soren If serial is working in a sense that you get a REPL prompt with a serial terminal like screen, then you could try Adafruit's ampy tool or Dave Hylands' rshell (https://github.com/dhylands/rshell). They both are pretty generic and allow to exchange scripts with the board and run them. This way, you can also set your board again for ftp. The script I use on my LoPy to set it to station mode is:

import network
import time
# setup as a station
wlan = network.WLAN(mode=network.WLAN.STA)
wlan.connect(ssid=MY_SSID, auth=(network.WLAN.WPA2, MY_PASSWD))
while not wlan.isconnected():
    time.sleep_ms(50)
wlan.ifconfig(config=(MY_FIXED_IP, "255.255.255.0", MY_GATEWAY,  MY_DNS))
print(wlan.ifconfig())

Obviously, you have to set the proper values for MY_xxx. If you do not need a fixed address, you can skip the line with wlan.ifconfig()

[soren]

@robert-hh thanks for the tip robert!

trying to connect my board with rshell now, and stuck at not knowing what "TYPE" or "TYPE_PARAMS" is supposed to mean in rshell.. the help method for connect method only says:

connect TYPE TYPE_PARAMS
connect serial port [baud]
connect telnet ip-address-or-name

EDIT:
Or the other parameters as well for that sake. I really don't understand when you make something like this, why not also make a good description and examples of everything.

[robert-hh]

@soren
e.g.
connect serial /dev/cu.xxxxx 115200
or
rshell -p /dev/cu.xxxx -b 115200
/dev/cu.xxxx ist the name of your serial port. On my linux machine, it's /dev/ttyUSB0
Once connected, /flash shows the TLD of WiPY or Lopy.
It works OK for file transfer and management. That should bring you back to the point where ftp works.

[soren]

@robert-hh it just keeps saying "connecting..." forever..
wondering if, because i put the wlan stuff in boot.py if this could have hampered the ability to connect to the board ? I mean if what I wrote was wrong and also placed before the uart is initialized?

[robert-hh]

Both rshell and ampy rely on a REPL prompt to be available. Did you try to connect with a simple serial terminal program like screen?

screen /dev/cu.xxxx 115200
Do you get the REPL prompt?
If not, then coding errors in boot.py before activating the UART may stop boot.py, and REPL on UART does not get active. Then, the step I would take is safe boot, which skips boot.py and main.py. Maybe that will set WiFi back to the initial state.

[robert-hh]

@soren If you are able to update the firmware via USB, then you can co the hard way: : erasing the flash and reflashing the image. I just tried that with my LoPy. That works, erases everything in the device and brings back the REPL prompt on UART, which is set active in a hidden
_boot.py in flash, which is executed before boot.py. All that requires, that you can reflash your device. Erasing the flash is easy, of you have the source tree installed. Then just call:
make erase
But all it needs is esptool.py form the repository, and the command.
python3 ./esptool.py --chip esp32 --port /dev/cu.xxxx --baud 480800 erase_flash
Then you could reload the software, connect through UART and a simple terminal program and setup WiFi manually step by step, e.g. using the first four statement of my sample script below.
I have placed an esptool.zip archive here, which is just a copy of the tree from esp-idf. https://github.com/robert-hh/Shared-Stuff

[soren]

@robert-hh

thanks

but safe boot doesn't set anything back, only goes into a temporary state where it bypasses boot.py and main.py as far as I can read. also the factory reset filesystem only seems possible when you have UART access...

[robert-hh]

@soren See my revived post below about erase & reflash

[soren]

@robert-hh hello robert, thanks for all the great help - it's really awesome!!

I managed to figure out, when booting in safe mode - that i can temporarily connect via ftp again (because the boot.py is bypassed).. and thus make changes to the boot.py.

soo.. the thing is though, that it seems the lopy does not care AT ALL about what I put into the boot.py script now, even after unplugging the short between G28 and 3v (which I assume should make it go back to loading boot and main).

EDIT
tinkering more about, it turned out I had to set the heartbeat to false in order to use the rgbled onboard the lopy. well done soren. anyway, it is indeed responding now, but setting up the thing with custom wlan configuration is really difficult. this topic has become pretty messy. I tried to change the topic name, but got a message that i couldn't.. it is pretty misleading atm. are there any admins on here?