Analog CO2 Sensor for LoPy, can 5v pin power it?

[robert-hh]

@ledbelly2142 The 5V pin is connected to the USB 5V or Vin. So it should source enough power to run the sensor. In you example, to use the attenuator, the syntach is:

adc = machine.ADC() # create an ADC object
apin = adc.channel(pin='P16', attn=machine.ADC.ATTN_11DB) # create an analog pin on P16 & connect CO2 sensor
value = apin()
print("ADC count = %d" %(value))

The value will never be 0, since the output of the sensor is in the range of 0.4..2 V. The esp32 is quite noisy, so you should average over a handful samples, like 10.

[ledbelly2142]

@jmarcelino
Thanks! yes, I only had 'import macine'
Now I get a reading, but it does not look like the sensor is working correctly. I am using ATTN_11DB to make the math conversion easier value * (3300/1024.0)
The raw ADC count is still high, at 883 and its not changing much.

Perhaps I am missing something in the documentation, is the ADC count a division of something? e.g. 883 count = 0.83v?

Thanks

[robert-hh]

@ledbelly2142 The range of the ADC is 0..4096. With an attenuation of 11DB, the reading of 883 tells 883*3.3/4096V = 0.71V

[ledbelly2142]

@robert-hh
Thanks, I could not find where in the documentation the ADC range?

The vendor of the CO2 sensor used the formula to get CO2 ppm:
value*(3300/1024)

I think there are 1024 is the steps on an arduino for the analog in.

So I think the step function to interpret the ppm should be:
value*(3300/4096) which would put us in the range of 711 ppm of CO2. Which sounds about right given that is on my desk right in front of me.

Thanks!

[ledbelly2142]

Here is what I used for this sensor:

import machine
from machine import ADC

adc = machine.ADC()               # create an ADC object
apin = adc.channel(pin='P16', attn=ADC.ATTN_11DB)   # create an analog pin on P16 & connect CO2 sensor

print("")
print("CO2 sensor Warming Up")
#time.sleep(180) # CO2 sensor needs 3 minutes to warm up
print("Reading CO2 Sensor...")
value = apin()
print("ADC count = %d" %(value))

# LoPy  has 1.1 V input range for ADC
co2 = value * (3300/4096.0)
print("CO2 Level = %5.1f ppm" % (co2))

[jmarcelino]

@ledbelly2142
The ADC is 12 bit so the range is 0..4095 as @robert-hh explained. The reference is 1.1 Volts.

At ATTN_11DB the full scale goes to 3.9V: 1.1 * math.pow(10.0, 11.0/20.0) so a more correct formula is value * (3900/4096)

Finally the sample code you linked doesn't just use the voltage reading (what you have now) as the concentration, it takes a few extra calculations.

    int voltage_diference=voltage-400;
    float concentration=voltage_diference*50.0/16.0;

I haven't read the datasheet but I guess you'll need to do the same in your code.

[ledbelly2142]

@jmarcelino
Thanks for your reply and help, I appreciate it. I understand the ADC bit range to 3900 instead of 3300--makes sense.

I am missing the voltage reading completely :( I was going on the ADC example code and explanations. It's gotta be in the documentation somewhere that I can't find. Even when I search the docs for 'voltage', only DAC shows up, not in ADC.

Why do we need the voltage difference -400 value?

How do I apply the concentration to get the value?
is that something like:

int voltage_diference=voltage-400
float concentration=voltage_diference*50.0/16.0
value = apin()
co2 = value * concentration(3900/4096.0)

Or would it just be

co2 = value * concentration

Thanks

[jmarcelino]

@ledbelly2142
I can't find any proper datasheet for your sensor but this plot shows everything you need to know:

At 0 ppm the sensor outputs 0.4v so you you need to subtract 400 (in millivolts) from your voltage reading (the voltage_diference in that formula)

Then you know that 0.4 volts to 2.0 volts (a 1.6 volt range or 0 to 1600 in your voltage_diference from above) equates to a range of 0 to 5000 ppm.

[ledbelly2142]

@jmarcelino
Thank you, makes sense now. Really appreciate it.
Cheers

[bmarkus]

Analog CO2 sensors does not really fit to todays IoT environment specially low power battery operated devices due to high power consumption and slow operation, long settle time. Take a look on Gas Sensing Solutions sensors. They are fast low power devices with digital interface. It is the data sheet of model I'm using with a LoRaWAN sensor (not PyCom), connected via serial line:

https://www.gassensing.co.uk/media/1050/cozir_ambient_datasheet_gss.pdf

[ledbelly2142]

@bmarkus
The COZIR sensors look nice. Are they in the sub $100 range? I also have CO2 sensors from co2meter.com, the K30. But they are a pain to work with and give very little support. At some point I wanted to create an I2C driver for micropython, but put it off because of the support. Another IoT option for low power gas sensors is Spec-Sensors We have used some of their stuff in the past, but they don't have CO2.

Thanks!

[ledbelly2142]

Here's the updated code for this sensor with everyone's help. @jmarcelino @robert-hh
In testing it, the results seem reasonable. Not super accurate but enough within 100ppm. Digy-Key has them for $58

import machine
from machine import ADC

adc = machine.ADC()               # create an ADC object
apin = adc.channel(pin='P16', attn=ADC.ATTN_11DB)   # create an analog pin on P16 & connect CO2 sensor

print("")
print("CO2 sensor Warming Up")
#need initial delay (180) # CO2 sensor needs 3 minutes to warm up
print("Reading CO2 Sensor...")
value = apin()
print("ADC count = %d" %(value))

# LoPy  has 1.1 V input range for ADC
co2 = (value-400) * (3900/4096.0)
print("CO2 Level = %5.1f ppm" % (co2))

[bmarkus]

@ledbelly2142 said in Analog CO2 Sensor for LoPy, can 5v pin power it?:

@bmarkus
The COZIR sensors look nice. Are they in the sub $100 range?

First hit of Google search gives $109 USD

https://www.co2meter.com/products/cozir-0-2-co2-sensor

As an indication you can visit the webshop of ChipCAD, a Hungarian distributor

https://shop.chipcad.hu/Welcome/Default.aspx?scenarioID=360&pid=1878

Prices are in HUF (Hungarian Forint), VAT not included. At the moment 1 USD = 262.6 HUF

But it may vary by distributor, quantity, shipping conditions, custom, etc. and model. You can ask GSS to advice where to buy it, they are good.