FiPy

• M

  spi on fopy
  fipy • • misterlisty  

  6
  0
  Votes
  6
  Posts
  1183
  Views

  

  @misterlisty From the docs "(spi_)id can only be 0". And you have to specify the MISO pin
• Y

  mqtt problem
  mqtt bugs • • yeffrimic  

  5
  0
  Votes
  5
  Posts
  1154
  Views

  Y

  @livius thanks man i solved it i create a folder in my project called lib then copy the raw code from the github. thanks
• K

  FiPy with LoRaWAN using AS923 channel plan
  lorawan as923 lorawan channel • • kompleteb  

  3
  0
  Votes
  3
  Posts
  1495
  Views

  K

  So this should do it, acknowledging that no channel willever use AS923 data rate 0 or 1? for channel in range(0, 15): lora.remove_channel(channel) lora.add_channel(0, frequency=923200000, dr_min=0, dr_max=3) lora.add_channel(1, frequency=923400000, dr_min=0, dr_max=3) lora.add_channel(2, frequency=922200000, dr_min=0, dr_max=3) lora.add_channel(3, frequency=922400000, dr_min=0, dr_max=3) lora.add_channel(4, frequency=922600000, dr_min=0, dr_max=3) lora.add_channel(5, frequency=922800000, dr_min=0, dr_max=3) lora.add_channel(6, frequency=922000000, dr_min=0, dr_max=3)
• T

  NB-IOT Non-IP Connectivity
  nb-iot • • Tweety  

  3
  0
  Votes
  3
  Posts
  1002
  Views

  T

  @jmarcelino sounds good! I'll follow-up in Q3-Q4, especially when the first APIs are exposed by the different MNOs to reach the SCEF
• X

  Send SMS with FiPy via LTE-M1 control plane
  fipy lte iot sms control plane • • X-Ryl  

  7
  0
  Votes
  7
  Posts
  3400
  Views

  A

  @jmarcelino ok, thx for this answer! Maybe i shoud introduce you into what my project is and you can tell me what the easiest way would be to implement this. In general i can say i want so send data from a Sensor to anywhere where i can catch the information from and i want so see it everywhere. This is what the IoT is for... ?. I don´t know realy much about programming, cellular network and internet protocols so my first idea was to send a sms or email. Now i know ist possible, but just with other providers or with detour. In my opinion it good to be independent as much as possible. I would like to use the internet via cellularnetwork . Thats why i chosed the GPY. The board can send from anywhere over LTE-NB-IoT. I hope in the near future i can put my sim-card inside the GPY and connect to the Internet. So this is the way i´ll send my data. Could this work?! :S But how to recieve and which transfer method would be good for sending via internet? Today i tried sending data with MQTT via WLAN. The example from https://www.hackster.io/bucknalla/mqtt-micropython-044e77 worked very good with my GPY! I also have seen that i can open my own MQTT-Server with https://mosquitto.org/ . Do you know: Would this also work with the LTE-module in the future? Is there a better solution you can recommend me? Maybe some thing with FTP- or MYSQL_Server(to heavy?)?! Thank you very much! Andy
• S

  PySense will not boot with FiPy
  bugs • • smbunn  

  3
  0
  Votes
  3
  Posts
  893
  Views

  S

  Tried two cables. Same result. One green flash. Nothing after that.
• L

  FiPy and WiPy communication - best practise? SPI, I2C, UART, Bluetooth, Wifi?
  fipy wipy uart spi ic2 • • Leo_Sol  

  9
  0
  Votes
  9
  Posts
  2351
  Views

  

  @leo_sol Looking at your initial post it seems that UART1 may still available on both units. the default config collides with the SD card pins, but you can assign UART1 to other pins.
• T

  Fresh FiPy - getting hot?! FW update (1.11.0.b1) not working...
  fipy firmware update temperature • • t.pirk  

  15
  0
  Votes
  15
  Posts
  3553
  Views

  D

  @xykon Thanks Xykon. Yes, I connected a wire between 23 and GND before plugging it in and flashing. I think if there are thermal issues affecting all Fipys and its a known issue you should slap a sticky note or something on the site. I mean all the Fipys just went out recently. t.pirk and myself can't be the only ones noticing this. Should we not use the Fipys until a fix is available? I don't want to damage my units.
• P

  Cannot import name Sigfox
  fipy sigfox import • • pymiom  

  11
  0
  Votes
  11
  Posts
  2842
  Views

  H

  @pymiom @mbartecki I got the new public firmware supporting Sigfox, by updating the device this morning! Enjoy guys :) Thank you @jmarcelino
• S

  FTDI drivers with FiPy+PyTrack in Win 7
  repl ftdi windows • • sandipg  

  14
  0
  Votes
  14
  Posts
  3101
  Views

  

  @sandipg The voltage and capacity are OK but it's the wrong connector, you want a JST PH-2 (also check the polarity as there is no standard) For Germany perhaps check out these two from HobbyKing: (the higher capacity 2000mAh is cheaper as it's on sale, but see dimensions etc) https://hobbyking.com/de_de/turnigy-2000mah-1s-1c-lipoly-w-2-pin-jst-ph-connector.html https://hobbyking.com/de_de/turnigy-1200mah-1s-1c-lipoly-w-2-pin-jst-ph-connector.html
• M

  FiPy unable to import LTE library
  fipy firmware lte • • markopraakli  

  5
  0
  Votes
  5
  Posts
  2322
  Views

  I

  We're hoping to use Telstra Australia