A
Hi @jcaron ! Thanks for your reply.
@jcaron said in MikroE AC Current Click on SPI:
@Anthony-Leung Did you also connect ground together, and are you correctly powering the sensor with 3.3 V (along with the right jumper setting on the sensor)?
Yes, the mikroE is wired to 3V3 on both the FiPy and the AC current sensor. The jumper uses 3V3 as standard so yes the hardware is correctly wired.
You probably need a small delay between /CS going high and going back low. It needs to stay high for at least 625 ns (tCSH) for each sample, not sure if your current code keeps it high long enough.
I've added a 1ms delay for the /CS based on your comment, seems to not make a difference thus far.
You may want to try different combinations of polarity and phase. The ADC chip on the sensor is supposed to work with both 0,0 (default for SPI) and 1,1.
Also have done this, no significant difference.
The ADC is a bit weird as it outputs 12 bits while SPI works on 8 bits. The ADC datasheet says it should still work by rearranging bits a bit like you're doing (though I'm not convinced by your shifts).
I've just read further into the data sheets and have adjusted it to the recommended bit shifts. I think it should now be correct following this description:
"The MCU receive register will contain the lowest-order seven bits and the B1 bit repeated as the A/D Converter has begun to shift out LSB first data with the extra clock. Typical procedure would then call for the lower-order byte of data to be shifted right by one bit to remove the extra B1 bit. The B7 bit is then transferred from the high-order byte to the lower-order byte, and then the higher-order byte is shifted one bit to the right as well"
To which I have done:
data = ((buf[0] << 7) | (buf[1] >> 1)) & 0xfff
What are you measuring? Is the current you're measuring constant (and known) or variable? What value are you expecting?
So far I've been trying to get a consistent value under no current, meaning it is not reading from any source. My assumption is that I should have a fairly consistent value with error however I am simply getting huge spikes in results. In my new segment of code I've measured the analog reading of the current as well to compare.
from machine import SPI
from machine import Pin
import machine
import time
# Analog pin settings
adc = machine.ADC()
apin = adc.channel(pin='P13')
val = apin()
# SPI settings
spi_cs = Pin('P23',mode=Pin.OUT)
spi_cs.value(True)
spi = SPI(0, mode=SPI.MASTER, baudrate=10000, bits=16, firstbit=SPI.MSB)
buf = bytearray(2)
while True:
spi_cs.value(False) # select the pin
time.sleep_ms(1) # wait
spi.readinto(buf) # read
data = ((buf[0] << 7) | (buf[1] >> 1)) & 0xfff # concatenate bytes and rearrange as per specs
val = apin() # retrieve analog output
print( "bits: ", "{0:16b}".format(data),
"\t spi: ", "{:10.4f}".format(30*data/4096), "A",
"\t analog: ", "{:10.4f}".format(30*val/4096), "A")
spi_cs.value(True) # deselect pin
time.sleep_ms(1) # wait
My results are:
bits: 0 spi: 0.0000 A analog: 1.1572 A
bits: 0 spi: 0.0000 A analog: 1.1353 A
bits: 111111111111 spi: 29.9927 A analog: 0.9448 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 1.1646 A
bits: 1110111111 spi: 7.0239 A analog: 1.0547 A
bits: 0 spi: 0.0000 A analog: 1.1133 A
bits: 111111111100 spi: 29.9707 A analog: 1.0620 A
bits: 111111111111 spi: 29.9927 A analog: 1.1279 A
bits: 111111111111 spi: 29.9927 A analog: 1.2817 A
bits: 111111111111 spi: 29.9927 A analog: 1.1206 A
bits: 0 spi: 0.0000 A analog: 1.2744 A
bits: 0 spi: 0.0000 A analog: 1.2378 A
bits: 111111111111 spi: 29.9927 A analog: 1.1646 A
bits: 111111111111 spi: 29.9927 A analog: 1.1938 A
bits: 111111111111 spi: 29.9927 A analog: 1.1353 A
bits: 0 spi: 0.0000 A analog: 1.1353 A
bits: 0 spi: 0.0000 A analog: 1.1646 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 1.0840 A
bits: 111111111111 spi: 29.9927 A analog: 0.9595 A
bits: 0 spi: 0.0000 A analog: 0.9155 A
bits: 0 spi: 0.0000 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 0.9448 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 0.9229 A
bits: 0 spi: 0.0000 A analog: 1.0547 A
bits: 0 spi: 0.0000 A analog: 1.0327 A
bits: 111111110000 spi: 29.8828 A analog: 1.0107 A
bits: 111111111111 spi: 29.9927 A analog: 1.1206 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 111111111 spi: 3.7427 A analog: 1.0107 A
bits: 0 spi: 0.0000 A analog: 1.0767 A
bits: 111111111100 spi: 29.9707 A analog: 0.9595 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 1.0986 A
bits: 0 spi: 0.0000 A analog: 1.0693 A
bits: 0 spi: 0.0000 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 1.0181 A
bits: 111111111111 spi: 29.9927 A analog: 1.0986 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 0 spi: 0.0000 A analog: 1.0767 A
bits: 0 spi: 0.0000 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 0 spi: 0.0000 A analog: 1.1426 A
bits: 0 spi: 0.0000 A analog: 1.1499 A
bits: 111111111111 spi: 29.9927 A analog: 1.0840 A
bits: 111111111111 spi: 29.9927 A analog: 1.2085 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 0 spi: 0.0000 A analog: 1.1206 A
bits: 0 spi: 0.0000 A analog: 1.2012 A
bits: 111111111111 spi: 29.9927 A analog: 1.0547 A
bits: 111111111111 spi: 29.9927 A analog: 1.0986 A
bits: 111111111111 spi: 29.9927 A analog: 1.0986 A
bits: 0 spi: 0.0000 A analog: 1.1719 A
bits: 0 spi: 0.0000 A analog: 1.0693 A
bits: 111111111111 spi: 29.9927 A analog: 1.0767 A
bits: 111111111111 spi: 29.9927 A analog: 1.1060 A
bits: 111111111111 spi: 29.9927 A analog: 1.1938 A
bits: 0 spi: 0.0000 A analog: 1.1865 A
bits: 0 spi: 0.0000 A analog: 1.1865 A
bits: 111111111111 spi: 29.9927 A analog: 1.0620 A
bits: 111111111111 spi: 29.9927 A analog: 1.1572 A
bits: 111111111111 spi: 29.9927 A analog: 1.1353 A
bits: 111011111 spi: 3.5083 A analog: 1.1279 A
So as you can see in the spi column there is a lot of fluctuation compared to analog readings. How should I go about this?
Thank you in advance again!
UPDATE
All good I have found the problem! I've connected the CLK and MISO pins in incorrectly.
