• SiPy hardware integration.

    SiPy sipy deep sleep power battery hardware
    7
    0 Votes
    7 Posts
    1k Views
    G
    Sorry, I misunderstood. I can only tell you that the Pygate mounting hole spacing is the same as the Expansionboard 3.0's spacing. We provide that here: https://docs.pycom.io/gitbook/assets/specsheets/Pycom_002_Specsheets_Pygate_v1.pdf in section 12. I will work on getting the Expansionboard spacing out there on its own page!
  • Battery options

    Discussion battery lora
    7
    0 Votes
    7 Posts
    3k Views
    N
    For that kind of longevity you're better off ditching the secondary cells (rechargeable) and going for a primary cell. I would recommend looking at the SAFT LS or LSH series. They are the best energy density to size batteries available.
  • 0 Votes
    5 Posts
    2k Views
    J
    @fsergeys You should measure power draw from battery, not USB. There's a lot more going on when powered via USB, it's not representative of what happens when you're running on battery. You can definitely use the Pytrack's deep sleep (use the PyTrack library) to power down completely the WiPy, but you shouldn't see much of a difference when running from battery in the case of a WiPy 3.
  • LOPY in case running on battery

    LoPy battery battery connect getting started new
    10
    0 Votes
    10 Posts
    3k Views
    robert-hhR
    @thr If you are using Pytrack, connect the battery to the dedicated battery connector on Pytrack.
  • SiPy Doesnt power up on LiPo battery

    Discussion sipy battery
    8
    0 Votes
    8 Posts
    2k Views
    A
    @bradnz I had your same problem. With the new release I solved
  • Lipo Rider V1.3 - measuring battery level

    Discussion lipo rider lipo battery adc
    4
    0 Votes
    4 Posts
    1k Views
    A
    @arthurlutz I'm using a Max17043 to read the State of Charge of a LiPo Battery, It sits between the battery and the charger or the wipy. (https://datasheets.maximintegrated.com/en/ds/MAX17043-MAX17044.pdf) sparkfun has a nice board for it (https://www.sparkfun.com/products/10617) It uses I2C to get the state. Even wrote a library for it (https://github.com/andrethemac/max17043.py). André
  • 1 Votes
    3 Posts
    1k Views
    M
    I am using the expansion board 2.0. I have no deep sleep shield yet (Pycom forgot to send the deep sleep shield with the order of the lopy 2 weeks ago. They told me a deep sleep shield is on its way now) We deinit the WLAN from start because we don't use it. We charge just using the micro-usb cable. It is configured with the jumpers at 450mA charge current. In the battery test we did, we intentionally drained the battery fully to see how long it would last. We expected the LoPy to stop working eventually, but expected we would be able to recharge it using the USB connection at that point. Can the deep sleep shield -if used on the LoPy 1- recharge a drained battery by just plugging the USB-cable in after the battery was exhausted and shut off by the deep sleep shield?
  • Powering the LoPy with 2 AA batteries?

    LoPy lopy power battery powered battery
    12
    0 Votes
    12 Posts
    4k Views
    J
    @robert-hh Things are much better now it's wired correctly! :-) The batteries and the converter have been at room temperature for the last few hours and my LoPy and sensor are working fine. Thanks again for your help Robert.
  • How to get power supply mode?

    Comments & Feedback battery
    3
    0 Votes
    3 Posts
    1k Views
    bmarkusB
    @jcaron Thanks, will check values.
  • Maximum battery voltage?

    Expansion Board battery lipo
    3
    0 Votes
    3 Posts
    1k Views
    B
    Many thanks!
  • LoPy - Running On Battery Information

    LoPy expansion board battery lopy
    1
    2 Votes
    1 Posts
    1k Views
    No one has replied
  • 0 Votes
    2 Posts
    1k Views
    D
    This is what I came with. I did some limited tests with LoPy connected to 5V supply. T2 drain was connected to 3V3 output of LoPy, VBAT to P16 (set as ADC channel) and EN signal to P20 (set as output). I could measure some voltage with the ADC while EN pin was enabled (3V3). When set to 0V, ADC reading was 0V as well and current through T2 drain was around 30nA (measured using uCurrent). [image: 1504793749529-battery_voltage_measurement_circuit_v1-resized.png] @daniel @jmarcelino and others please comment if this circuit makes sense in your opinion. The goal is to limit the current through the voltage divider in between measurements - e.g. during deep-sleep of battery powered sensor.
  • Solar Lipo charger

    LoPy solar battery charger lopy
    6
    0 Votes
    6 Posts
    2k Views
    robert-hhR
    @JimT Sorry, I could have told you. You may use a 1N4001 model (or any of the 1N400x series). You have to put that in series to the solar module, Anode of the diode at the + pin of the solar module, Kathode (the side with the ring on the diode case) to the charger module's + input. Doing that, the voltage of the solar panel will be reduced by about 0.7 V. I would add a small load too behind the diode, to cap the no-load case, like by a 1 k resistor at the chargers module input between + and GND. You can use the additional power in lead pads of the charger module for that. I see that the module has already a built in diode, but that is a MPB120 Schottky type and reduces the Voltage only by 0.3 V.
  • 0 Votes
    4 Posts
    3k Views
    ledbelly2142L
    @jmarcelino Once again, thanks for the great feedback. I was looking for a simple way to alert when the battery needs to be recharged. Looks like some simple logic could be: if voltages gets to 3.3, alert for recharge... So many LiPo batteries have differing characteristics, even among the same model/make/capacity/manufacturer. I don't think there is real value is tracking a percentage... without extensive battery testing. Simplest thing to do is just report voltage. From the example from HERE do you recommend using the following: numADCreadings = const(100) def ADCloopMeanStdDev(): adc = machine.ADC(0) adcread = adc.channel(attn=1, pin='P16') samplesADC = [0.0]*numADCreadings; meanADC = 0.0 i = 0 while (i < numADCreadings): adcint = adcread() samplesADC[i] = adcint meanADC += adcint i += 1 meanADC /= numADCreadings varianceADC = 0.0 for adcint in samplesADC: varianceADC += (adcint - meanADC)**2 varianceADC /= (numADCreadings - 1) print("%u ADC readings :\n%s" %(numADCreadings, str(samplesADC))) print("Mean of ADC readings (0-1023) = %15.13f" % meanADC) print("Mean of ADC readings (0-1400 mV) = %15.13f" % (meanADC*1400/1024)) print("Variance of ADC readings = %15.13f" % varianceADC) print("10**6*Variance/(Mean**2) of ADC readings = %15.13f" % ((varianceADC*10**6)//(meanADC**2))) print("ADC reading for Voltage (0-1400 mV) = %15.4f" % (meanADC*1400/1024)) From the ACD pin 16 voltage, the voltage is the meanACD*1400/1024 Does not seem right, the output is 4966.3634.
  • 0 Votes
    5 Posts
    2k Views
    T
    I had simmilar issue using VIN. I can't believe Pycom doesn't provide any schematic for these expansion boards, or atleast proper descriptions on how they can be used. I was also under the impression that VIN can be used as an input, instead of using the USB. There are NO WARNINGS anywhere that you should not be using VIN as an input, while using a battery as a backup. Luckily my house didn't burn down as I soon enough figured out that VIN and the Battery + seem to be linked together... I'm new to Pycom's hardware - and thus far really disappointed in the lack of usefull (and up to date) documentation
  • Voltage regulator for primary battery

    Getting Started battery regulator oem
    21
    0 Votes
    21 Posts
    6k Views
    L
    @miroslav-petrov said in Voltage regulator for primary battery: LTC3335 But it is quite expensive or maybe i am looking wrongly...
  • 0 Votes
    1 Posts
    983 Views
    No one has replied
  • battery and TPS2115A

    Comments & Feedback battery tps2115a
    2
    0 Votes
    2 Posts
    974 Views
    J
    @NicolaC The Expansion board 2.0 does not provide status of the TPS2115A and battery charge is only available via the voltage divider connected to the ADC (not very accurate, especially for LiPos) But the status of the TPS2115A power mux could good idea for future improvements and/or a Coloumb counter.
  • 18650 Li-Ion battery

    Expansion Board battery expansion board lipo battery
    3
    1 Votes
    3 Posts
    2k Views
    T
    @cfaessler Did you eventually tried the 18650? Can you share some experience? Thanks!
  • 2 cell Lipo battery

    Discussion battery
    2
    0 Votes
    2 Posts
    862 Views
    J
    @cfaessler No, the maximum input voltage is 5.5V. You'd have to use an external regulator.