• 0 Votes
    4 Posts
    2k Views
    S
    @jcaron Thanks for the tip. Output below. from pytrack import Pytrack py = Pytrack() py.read_fw_version() 4 Which I think means it had flashed successfully (partly as my previously loaded libs had disappeared!). I had tried to connect the External I/O header as an alternative but had similar lack of luck. Tried High speed transfer both ticked and unticked based on reading another similar post. Just tried this again with same result. Flash tool states it is connecting... then shows a Failure! warning. The only COM port in the drop down is COM3 but I am not sure that's the attached PyTrack as removing the PyTrack from USB doesn't de-list the item listed in Device Manager. I am still concerned that it is more related to not having the correct Windows drivers in place that's preventing things from working as they should. Thanks again for the response. Regards Shaun
  • Pytrack, usb serial communication and REPL

    Getting Started uart repl usb pytrack
    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • [SOLVED] Cannot Connect

    Getting Started firmware usb connection connection prob
    4
    0 Votes
    4 Posts
    5k Views
    T
    USB issues SOLVED The problem was the baud rate being used by Putty. The default baud rate in Putty is 9600 but the rate that should be used is 115200. This is mentioned in the documentation section for using Linux . After I changed the baud rate to 115200 did that Serial USB was working.
  • Mac OS USB device disappears

    Expansion Board osx usb atom
    9
    0 Votes
    9 Posts
    4k Views
    T
    @jmarcelino $ ioreg -p IOUSB +-o Root <class IORegistryEntry, id 0x100000100, retain 15> +-o Root Hub Simulation Simulation@14000000 <class AppleUSBRootHubDevice, id 0x10000034b, registered, matched, active, busy 0 (0 ms), retain 10> +-o Bluetooth USB Host Controller@14300000 <class AppleUSBDevice, id 0x1000003f2, registered, matched, active, busy 0 (1 ms), retain 21> +-o FT230X Basic UART@14100000 <class AppleUSBDevice, id 0x1000005dd, registered, matched, active, busy 0 (15 ms), retain 14> This is the output when the wipy is connected, and right now it's working fine. I'll run the command again if the problem re-occurs. Thanks, Bernhard
  • Pycom boards as mass storage devices

    Discussion usb storage
    3
    0 Votes
    3 Posts
    1k Views
    D
    @jmarcelino I see. Thanks for the links, mpfshell seems to support recursive uploading and appears to be generally awesome :) I'll give it a try.
  • Cannot update firmware on new WiPy v 1.3

    WiPy 2&3 wipy firmware update usb
    2
    2
    0 Votes
    2 Posts
    1k Views
    robert-hhR
    You cannot use the pycom updater for a Wipy 1.x. These have to be updated via OTA. Images and instructions are on the micopython.org web site. There is also the forum for that product.
  • 0 Votes
    7 Posts
    2k Views
    P
    @jmarcelino Thank you!!! you saved my day, it works!
  • 0 Votes
    9 Posts
    3k Views
    H
    Ok..it works again using /dev/cu.usbmodemP* device. That confused me...usually its always a tty. Thanks a lot!!
  • [SOLVED] Linux pytrack USB to serial

    Getting Started usb serial linux pytrack
    10
    0 Votes
    10 Posts
    4k Views
    Tamm BuhezT
    @jacquej1 You should create a new post as your problem is really different from the original I posted to avoid confusing people. That beeing said, I see a typo on address path "/dev/ttyUS0" should be /dev/ttyUSB0" If you want to continue the discussion please create a new topic.
  • 0 Votes
    10 Posts
    4k Views
    L
    @robert-hh said in Update LoPy firmware using Pysense as expansion board: So better never supply the board by the 3.3V Pin. That's an output, not an input. Use the Vin Pin for supply. @daniel: Please remove note, that the device can be supplied through the 3.3V pin. Even if that may work under certain conditions, the risk is too high that devices will be broken. I see that we disscuss this 6 months ago ;-) https://forum.pycom.io/topic/316/wipy-pin-3v3-not-work But conclusion was different. Now when we have schematic i do not see there any diode or something like LTC4357 And schematic(and description) for LM3281 does not bring light if there is some protection - especially that there is comparator output
  • Cannot connect to WiPy 2.0 via USB

    WiPy 2&3 usb wipy2.0 expansionboard
    6
    0 Votes
    6 Posts
    3k Views
    H
    Solved! These are the right drivers to install! http://www.ftdichip.com/Drivers/D2XX.htm
  • 0 Votes
    32 Posts
    15k Views
    sorenS
    @robert-hh hello robert, thanks for all the great help - it's really awesome!! I managed to figure out, when booting in safe mode - that i can temporarily connect via ftp again (because the boot.py is bypassed).. and thus make changes to the boot.py. soo.. the thing is though, that it seems the lopy does not care AT ALL about what I put into the boot.py script now, even after unplugging the short between G28 and 3v (which I assume should make it go back to loading boot and main). EDIT tinkering more about, it turned out I had to set the heartbeat to false in order to use the rgbled onboard the lopy. well done soren. anyway, it is indeed responding now, but setting up the thing with custom wlan configuration is really difficult. this topic has become pretty messy. I tried to change the topic name, but got a message that i couldn't.. it is pretty misleading atm. are there any admins on here?
  • 0 Votes
    14 Posts
    4k Views
    S
    SOLVED - I powered the stepper motor separately and all is good. I'm guessing there were transient demands in excess of the 800mA I could measure that were causing problems.
  • Max voltage input on USB port

    Expansion Board voltage usb
    6
    0 Votes
    6 Posts
    5k Views
    N
    Hi...i am a new user here. As per my knowledge 5.6v is out of spec and should be considered unsafe. Most likely it will work, since USB ports tend to be poorly regulated and these devices take that into account with lots of safety margin, but you risk your player doing so. You might want to look into putting together a 5v regulator circuit to be safe. complete pcb
  • No serial-over-USB connection to expansion board

    WiPy 2&3 wipy ftdi serial usb
    10
    0 Votes
    10 Posts
    4k Views
    S
    got similar error, my expansion board doesnt show as recognized